- 您現在的位置：買賣IC網 > PDF目錄97995 > L6470HTR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 7 A, PDSO28 PDF資料下載
參數資料
| 型號： | L6470HTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 7 A, PDSO28 |
| 封裝： | ROHS COMPLIANT, HTSSOP-28 |
| 文件頁數： | 19/64頁 |
| 文件大?。?/td> | 814K |
| 代理商： | L6470HTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Functional description
L6470
26/64
Doc ID 16737 Rev 2
The overcurrent threshold can be programmed through the OCD_TH register in one of 16
available values ranging from 375 mA to 6 A with steps of 375 mA (see Table 8, paragraph
It is possible to set if an overcurrent event causes or not the MOSFETs turn-off (bridges in
high impedance status)acting on OC_SD bit in the CONFIG register (see paragraph 9.1.21).
6.10
Undervoltage lock-out (UVLO)
The L6470 provides a motor supply UVLO protection. When the motor supply voltage falls
below the VSthOff threshold voltage, STATUS register UVLO flag is forced low. When a
GetStatus command is sent to the IC, and the undervoltage condition is expired, the UVLO
the motor supply voltage goes over the VSthOn threshold voltage. When the device is in
undervoltage condition no motion command can be performed. UVLO flag is forced low by
logic reset (power-up included) even if no UVLO condition is present.
6.11
Thermal warning and thermal shutdown
An internal sensor allows the L6470 to detect when the device internal temperature exceeds
a thermal warning or an overtemperature threshold.
When the thermal warning threshold (Tj(WRN)) is reached the TH_WRN bit in the STATUS
register is forced low (see paragraph 9.1.22) until the temperature decrease below Tj(WRN)
When the thermal shutdown threshold (Tj(OFF)) is reached the device goes in thermal
shutdown condition: the TH_SD bit in the STATUS register is forced low, the power bridges
are disabled bridges in high impedance state and the HiZ bit in the STATUS register is
raised (see paragraph 9.1.22).
Thermal shutdown condition only expires when the temperature goes below the thermal
warning threshold (Tj(WRN)).
On exit from thermal shutdown condition the bridges are still disabled (HiZ flag high);
whichever motion command makes the device exiting from High Z state (HardStop and
SoftStop included).
6.12
Reset and standby
The device can be reset and put into standby mode through a dedicated pin. When
STBY\RST pin is driven low, the bridges are left open (High Z state), the internal charge
pump is stopped, the SPI interface and control logic are disabled and the internal 3 V
voltage regulator maximum output current is reduced to IREG,STBY; as a result the L6470
heavily reduces the power consumption. At the same time the registers values are reset to
default and all protection functions are disabled. STBY\RST input has to be forced low at
least for tSTBY,min in order to ensure the complete switch to standby mode.
On exit from standby mode, as well as for IC power-up, a delay of up to tlogicwu must be
given before applying a new command to allow proper oscillator and logic startup and a
delay of up to tcpwu must be given to allow the charge pump startup.
相關PDF資料 |
PDF描述 |
|---|---|
| L6562DTR | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6562D | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6563HTR | POWER FACTOR CONTROLLER, PDSO16 |
| L6563H | POWER FACTOR CONTROLLER, PDSO16 |
| L6565N | 0.7 A SWITCHING CONTROLLER, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6470HTR-CUT TAPE | 制造商:ST 功能描述:L6470H Series 45 V Quad Output dSPIN Microstepping Motor Driver - HTSSOP-28 |
| L6470PD | 功能描述:馬達/運動/點火控制器和驅動器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6470PDTR | 功能描述:馬達/運動/點火控制器和驅動器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L64710GC-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
| L64710GC-40 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
發布緊急采購，3分鐘左右您將得到回復。