- 您現在的位置：買賣IC網 > PDF目錄97995 > L6470HTR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 7 A, PDSO28 PDF資料下載
參數資料
| 型號： | L6470HTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 7 A, PDSO28 |
| 封裝： | ROHS COMPLIANT, HTSSOP-28 |
| 文件頁數： | 20/64頁 |
| 文件大?。?/td> | 814K |
| 代理商： | L6470HTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
L6470
Functional description
Doc ID 16737 Rev 2
27/64
On exit from standby mode the bridges are disabled (HiZ flag high) and whichever motion
command makes the device exiting from High Z state (HardStop and SoftStop included).
Caution:
It is not recommended to reset device when outputs are active. The device should be
switched to high impedance state before being reset.
6.13
External switch (SW pin)
The SW pin sources a current towards an external switch in order to test whether it is
CLOSED or OPEN: the SW input is internally pulled-up to VDD and detects if the pin is open
or connected to ground (see Figure 11).
The SW_F bit of STATUS register indicates if the switch is open (‘0’) or closed (‘1’) (see
paragraph 9.1.22); the bit value is refreshed at every system clock cycle (125 ns). SW_EVN
flag of STATUS register is raised when a switch turn-on event (SW input falling edge) is
detected (see paragraph 9.1.22). A GetStatus command releases the SW_EVN flag (see
paragraph 9.2.20.
By default a switch turn-on event causes a HardStop interrupt (SW_MODE bit of CONFIG
register set to ‘0’). Otherwise (SW_MODE bit of CONFIG register set to ‘1’), switch input
events do not cause interrupts and the switch status information are at user disposal (see
The switch input can used by GoUntil and ReleaseSW commands as described in
If the SW input is not used, it should be connected to VDD.
Figure 11.
External switch connection
相關PDF資料 |
PDF描述 |
|---|---|
| L6562DTR | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6562D | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6563HTR | POWER FACTOR CONTROLLER, PDSO16 |
| L6563H | POWER FACTOR CONTROLLER, PDSO16 |
| L6565N | 0.7 A SWITCHING CONTROLLER, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6470HTR-CUT TAPE | 制造商:ST 功能描述:L6470H Series 45 V Quad Output dSPIN Microstepping Motor Driver - HTSSOP-28 |
| L6470PD | 功能描述:馬達/運動/點火控制器和驅動器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6470PDTR | 功能描述:馬達/運動/點火控制器和驅動器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L64710GC-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
| L64710GC-40 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Encoder/Decoder |
發布緊急采購，3分鐘左右您將得到回復。