- 您現在的位置：買賣IC網 > PDF目錄383133 > ISL5216 (Intersil Corporation) Four-Channel Programmable Digital DownConverter PDF資料下載
參數資料
| 型號： | ISL5216 |
| 廠商： | Intersil Corporation |
| 英文描述： | Four-Channel Programmable Digital DownConverter |
| 中文描述： | 四通道可編程數字下變頻器 |
| 文件頁數： | 44/65頁 |
| 文件大?。?/td> | 1384K |
| 代理商： | ISL5216 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
44
TABLE 38. BUS ROUTING CONTROL REGISTER (GWA = F801h)
P(31:0)
FUNCTION
31:24
Unused - set to zero.
23:20
Interrupt pulse width. The width of the interrupt pulse at the pin can be programmed to be from 1 to 15 clocks wide. Program with the
desired number of clocks. (NOTE: The pulse counter is only reset with the RESET pin. If a channel is reset by software or a SYNCI,
any interrupt pulse in process will finish).
19:17
Set to 0.
16
CH1 or CH3 AGC to CH0 ext AGC. This bit selects whether the AGC loop filter output from CH1 or CH3 is routed to the external
AGC gain input of CH0. 0=CH3, 1=CH1.
15:14
CH3 ext source mux sel. These bits select whether the CH2 source mux, CIC2, or FIR2out is routed to the external input of FIR3.
0=CH2srcmux, 1=FIR2, 2=CIC2.
13
CH2 ext source mux sel. This bit selects whether the CH1 external source mux or FIR1out is routed to the external input of FIR2.
0=CH1srcmux, 1=FIR1out.
12
CH1 ext source mux sel. This bit selects whether the CIC0 output or FIR0out is routed to the external input of FIR1. 0=CIC0,
1=FIR0out.
11
Set to 0.
10
CH1 backend input sel 0=CIC1, 1=CH1 ext src mux.
9
CH2 backend input sel 0=CIC2, 1=CH2 ext src mux.
8
CH3 backend input sel 0=CIC3, 1=CH3 ext source mux.
7
CH0 Ext AGC input enable. 0=CH0 loop filt, 1=external input.
6
CH1 Ext AGC input enable 0=CH1 loop filt, 1=external input.
5
CH2 Ext AGC input enable 0=CH2 loop filt, 1=external input.
4
CH3 Ext AGC input enable Set to 0.
3
CH0 enable serial output 1=FIR0 out enabled to serial outputs.
2
CH1 enable serial output 1=FIR1 out enabled to serial outputs.
1
CH2 enable serial output 1=FIR2 out enabled to serial outputs.
0
CH3 enable serial output 1=FIR3 out enabled to serial outputs.
TABLE 39. RESET/SYNC/INTERRUPT SOURCE SELECTION REGISTER (GWA = F802h)
P(31:0)
FUNCTION
31
When set, an interrupt will be generated on each data output of channel 0 to the output block. Typically, this bit will only be set for
one channel.
30
When set, the data input to the part will be disabled (the input enable will be zeroed and held at zero) on a
μ
P reset (this is always
true for the reset pin, whether this bit is set or not, and additionally, the reset pin sets the input mode to gated). The input enable will
be released for the input sample that aligns with the SYNCI signal. This is a method for starting up the processing synchronous with
a particular data sample.
29
When this bit is set, the carrier center frequency will be updated from the holding register (IWA = *005h) to the active register on the
SYNCI signal. If the bit is set in register IWA = *004h to clear the phase accumulator feedback on loading, this function will
synchronize the phase of multiple channels. After initial synchronization, the bit in IWA = *004h can be cleared and updates will be
synchronous and phase continuous across channels.
28
When this bit is set, the FIR filter compute engine is reset on SYNCI. Resetting the FIR filter compute engine requires 32 clock (CLK)
cycles to initialize the read and write pointers.
27
When this bit is set, the AGC is reset on SYNCI.
26
This bit has the same function as bit 29, but for the timing (resampler) NCO. The bit to zero the phase accumulator feedback is in
register IWA = *00Ah.
25
When this bit is set, the CIC decimation counter is reset on SYNCI.
24
When this bit is set, the serial output block is reset on SYNCI. If bit 4 in location GWA F803h is set, the serial clock divider is also reset.
23:16
Same functions as 31:24 for channel 1.
15:8
Same functions as 31:24 for channel 2.
7:0
Same functions as 31:24 for channel 3.
ISL5216
相關PDF資料 |
PDF描述 |
|---|---|
| ISL5217EVAL1 | Quad Programmable Up Converter |
| ISL5217KI | Quad Programmable Up Converter |
| ISL5217 | Quad Programmable Up Converter |
| ISL5217KIZ | Quad Programmable Up Converter |
| ISL5314INZ | Direct Digital Synthesizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL5216_05 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Four-Channel Programmable Digital DownConverter |
| ISL5216_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Four-Channel Programmable Digital Downconverter |
| ISL5216EVAL1 | 功能描述:EVALUATION BOARD FOR ISL5216KI RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796 |
| ISL5216KI | 功能描述:上下轉換器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,0.8M RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| ISL5216KI-1 | 功能描述:上下轉換器 QUAD DIGITAL DOWNCONVERTER,IND TEMP,1.OMM PITCH BGA PACKAG RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
發布緊急采購，3分鐘左右您將得到回復。