- 您現在的位置：買賣IC網 > PDF目錄384519 > ISL1209 (Intersil Corporation) Low Power RTC with Battery Backed SRAM and Event Detection PDF資料下載
參數資料
| 型號： | ISL1209 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Power RTC with Battery Backed SRAM and Event Detection |
| 中文描述： | 低功耗RTC與電池供電SRAM和事件檢測 |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 416K |
| 代理商： | ISL1209 |
8
FN6109.1
September 27, 2005
has occurred and requests action. It is an open drain
active low output.
Frequency Output Mode.
The pin outputs a clock signal
which is related to the crystal frequency. The frequency
output is user selectable and enabled via the I
2
C bus. It is
an open drain active low output.
Serial Clock (SCL)
The SCL input is used to clock all serial data into and out of
the device. The input buffer on this pin is always active (not
gated). It is disabled when the backup power supply on the
V
BAT
pin is activated to minimize power consumption.
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into and out
of the device. It has an open drain output and may be ORed
with other open drain or open collector outputs. The input
buffer is always active (not gated) in normal mode.
An open drain output requires the use of a pull-up resistor.
The output circuitry controls the fall time of the output signal
with the use of a slope controlled pull-down. The circuit is
designed for 400kHz I
2
C interface speeds. It is disabled
when the backup power supply on the V
BAT
pin is activated.
V
DD
, GND
Chip power supply and ground pins. The device will operate
with a power supply from V
DD
=2.7V to 5.5VDC. A 0.1μF
capacitor is recommended on the V
DD
pin to ground.
Functional Description
Power Control Operation
The power control circuit accepts a V
DD
and a V
BAT
input.
Many types of batteries can be used with Intersil RTC
products. For example, 3.0V or 3.6V Lithium batteries are
appropriate, and battery sizes are available that can power
the ISL1209 for up to 10 years. Another option is to use a
Super Cap for applications where V
DD
is interrupted for up
to a month. See the Applications Section for more
information.
Normal Mode (V
DD
) to Battery Backup Mode
(V
BAT
)
To transition from the V
DD
to V
BAT
mode, both of the
following conditions must be met:
Condition 1:
V
DD
< V
BAT
- V
BATHYS
where V
BATHYS
≈
50mV
Condition 2:
V
DD
< V
TRIP
where V
TRIP
≈
2.2V
Battery Backup Mode (V
BAT
) to Normal Mode
(V
DD
)
The ISL1209 device will switch from the V
BAT
to V
DD
mode
when one of the following conditions occurs:
Condition 1:
V
DD
> V
BAT
+ V
BATHYS
where V
BATHYS
≈
50mV
Condition 2:
V
DD
> V
TRIP
+ V
TRIPHYS
where V
TRIPHYS
≈
30mV
These power control situations are illustrated in Figures 9
and 10.
The I
2
C bus is deactivated in battery backup mode to provide
lower power. Aside from this, all RTC functions are
operational during battery backup mode. Except for SCL and
SDA, all the inputs and outputs of the ISL1209 are active
during battery backup mode unless disabled via the control
register. The User SRAM is operational in battery backup
mode down to 1.8V.
Power Failure Detection
The ISL1209 provides a Real Time Clock Failure Bit (RTCF)
to detect total power failure. It allows users to determine if
the device has powered up after having lost all power to the
device (both V
DD
and V
BAT
).
Low Power Mode
The normal power switching of the ISL1209 is designed to
switch into battery backup mode only if the V
DD
power is
lost. This will ensure that the device can accept a wide range
of backup voltages from many types of sources while reliably
switching into backup mode. Another mode, called Low
V
BAT
- V
BATHYS
V
BAT
V
BAT
+ V
BATHYS
BATTERY BACKUP
MODE
V
DD
V
TRIP
2.2V
1.8V
FIGURE 9. BATTERY SWITCHOVER WHEN V
BAT
< V
TRIP
FIGURE 10. BATTERY SWITCHOVER WHEN V
BAT
> V
TRIP
V
TRIP
V
BAT
V
TRIP
+ V
TRIPHYS
BATTERY BACKUP
MODE
V
DD
V
TRIP
3.0V
2.2V
ISL1209
相關PDF資料 |
PDF描述 |
|---|---|
| ISL1209IU10-TK | Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL1209IU10Z | Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL22416 | Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL22419 | Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL22426 | Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL1209_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL1209EVAL | 制造商:Intersil Corporation 功能描述:ISL1209 EVALUATION BOARD - Bulk |
| ISL1209EVALZ | 制造商:Intersil Corporation 功能描述:ISL1209EVALZ (PB-FREE ) EVALUATION BOARD - ROHS COMPLIANT - Rail/Tube |
| ISL1209IP18 | 制造商:Intersil Corporation 功能描述:LOW POWER RTC WITH BATTERY BACKED SRAM PDIP 18 - Rail/Tube |
| ISL1209IU10 | 功能描述:IC RTC/CALENDAR I2C 10-MSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。