- 您現在的位置：買賣IC網 > PDF目錄384519 > ISL1209 (Intersil Corporation) Low Power RTC with Battery Backed SRAM and Event Detection PDF資料下載
參數資料
| 型號： | ISL1209 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Power RTC with Battery Backed SRAM and Event Detection |
| 中文描述： | 低功耗RTC與電池供電SRAM和事件檢測 |
| 文件頁數： | 23/24頁 |
| 文件大?。?/td> | 416K |
| 代理商： | ISL1209 |
23
FN6109.1
September 27, 2005
Below are some examples with equations to assist with
calculating backup times and required capacitance for the
ISL1209 device. The backup supply current plays a major
part in these equations, and a typical value was chosen for
example purposes. For a robust design, a margin of 30%
should be included to cover supply current and capacitance
tolerances over the results of the calculations. Even more
margin should be included if periods of very warm
temperature operation are expected.
Example 1. Calculating backup time given
voltages and capacitor value
In Figure 21, use C
BAT
= 0.47F and VDD = 5.0V. With V
DD
=
5.0V, the voltage at V
BAT
will approach 4.7V as the diode
turns off completely. The ISL1209 is specified to operate
down to V
BAT
= 1.8V. The capacitance charge/discharge
equation is used to estimate the total backup time:
Rearranging gives
C
BAT
is the backup capacitance and dV is the change in
voltage from fully charged to loss of operation. Note that
I
TOT
is the total of the supply current of the ISL1209 (I
BAT
)
plus the leakage current of the capacitor and the diode, I
LKG
.
In these calculations, I
LKG
is assumed to be extremely small
and will be ignored. If an application requires extended
operation at temperatures over 50°C, these leakages will
increase and hence reduce backup time.
Note that I
BAT
changes with V
BAT
almost linearly (see
Typical Performance Curves). This allows us to make an
approximation of I
BAT
, using a value midway between the
two endpoints. The typical linear equation for I
BAT
vs. V
BAT
is:
Using this equation to solve for the average current given 2
voltage points gives:
Combining with Equation 2 gives the equation for backup
time:
where
C
BAT
= 0.47F
V
BAT2
= 4.7V
V
BAT1
= 1.8V
I
LKG
= 0 (assumed minimal)
Solving equation 4 for this example, I
BATAVG
= 4.387E-7 A
T
BACKUP
= 0.47 * (2.9) / 4.38E-7 = 3.107E6 sec
Since there are 86,400 seconds in a day, this corresponds to
35.96 days. If the 30% tolerance is included for capacitor
and supply current tolerances, then worst case backup time
would be:
C
BAT
= 0.70 * 35.96 = 25.2 days
Example 2. Calculating a capacitor value for a
given backup time
Referring to Figure 21 again, the capacitor value needs to be
calculated to give 2 months (60 days) of backup time, given
VDD = 5.0V. As in Example 1, the V
BAT
voltage will vary
from 4.7V down to 1.8V. We will need to rearrange Equation
2 to solve for capacitance:
Using the terms described above, this equation becomes:
where
T
BACKUP
= 60 days * 86,400 sec/day = 5.18 E6 sec
I
BATAVG
= 4.387 E-7 A (same as Example 1)
I
LKG
= 0 (assumed)
V
BAT2
= 4.7V
V
BAT1
= 1.8V
Solving gives
C
BAT
= 5.18 E6 * (4.387 E-7)/(2.9) = 0.784F
If the 30% tolerance is included for tolerances, then worst
case cap value would be
C
BAT
= 1.3 *.784 = 1.02F
FIGURE 21. SUPERCAPACITOR CHARGING CIRCUIT
2.7V to 5.5V
VDD
V
BAT
GND
1N4148
C
BAT
I = C
BAT
* dV/dT
(EQ. 1)
dT = C
BAT
* dV/I
TOT
to solve for backup time.
(EQ. 2)
I
BAT
= 1.031E-7*(V
BAT
) + 1.036E-7 Amps
(EQ. 3)
I
BATAVG
= 5.155E-8*(V
BAT2
+ V
BAT1
) + 1.036E-7 Amps
(EQ. 4)
T
BACKUP
= C
BAT
* (V
BAT2
- V
BAT1
) / (I
BATAVG
+ I
LKG
)
seconds
(EQ. 5)
C
BAT
= dT*I/dV
(EQ. 6)
C
BAT
= T
BACKUP
* (I
BATAVG
+ I
LKG
)/(V
BAT2
– V
BAT1
)
(EQ. 7)
ISL1209
相關PDF資料 |
PDF描述 |
|---|---|
| ISL1209IU10-TK | Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL1209IU10Z | Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL22416 | Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL22419 | Low Noise, Low Power, SPI Bus, 128 Taps, Wiper Only(低噪聲,低功率，SPI總線, 128抽頭電位器) |
| ISL22426 | Low Noise, Low Power, SPI Bus, 128 Taps(低噪聲,低功率，SPI總線, 128抽頭電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL1209_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL1209EVAL | 制造商:Intersil Corporation 功能描述:ISL1209 EVALUATION BOARD - Bulk |
| ISL1209EVALZ | 制造商:Intersil Corporation 功能描述:ISL1209EVALZ (PB-FREE ) EVALUATION BOARD - ROHS COMPLIANT - Rail/Tube |
| ISL1209IP18 | 制造商:Intersil Corporation 功能描述:LOW POWER RTC WITH BATTERY BACKED SRAM PDIP 18 - Rail/Tube |
| ISL1209IU10 | 功能描述:IC RTC/CALENDAR I2C 10-MSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。