- 您現在的位置：買賣IC網 > PDF目錄360993 > ISD-SR3000 PDF資料下載
參數資料
| 型號： | ISD-SR3000 |
| 文件頁數： | 48/120頁 |
| 文件大?。?/td> | 1293K |
| 代理商： | ISD-SR3000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
2-7
2—SOFTWARE
ISD-SR3000
ISD
MWRQST
MICROWIRE Request. When active (0), this signal indicates that new status information is
available. MWRQST is deactivated (set to 1), after the ISD-SR3000 receives a GSW (Get Sta-
tus Word) command from the host controller. After reset, this signal becomes active (0) to indi-
cate that a reset occurred. MWRQST, unlike all the signals of the communication protocol, is
an asynchronous line that is controlled by the ISD-SR3000 firmware.
2.5.3
After reset, both MWRQST and MWRDY are cleared to 0.
SIGNAL USE IN THE INTERFACE PROTOCOL
The MWRQST signal is activated to indicate that a reset occurred. The EV_RESET bit in the
status register is used to indicate a reset condition.
The GSW command should be issued after reset to verify that the EV_RESET event occurred,
and to deactivate the MWRQST signal.
While the MWCS signal is active (0), the ISD-SR3000 reads data from MWDIN on every rising
edge of MWCLK. The ISD-SR3000 also writes every bit back to MWDOUT. This bit is either the
same bit, which was read from MWDIN (in this case it is written back as a synchronization echo
after some propagation delay), or it is a bit of a value the ISD-SR3000 transmits to the host con-
troller (in this case it is written on every falling edge of the clock).
When a command has more than one parameter/return-value, the parameters/return-values
are transmitted in the order of appearance. If a parameter/return-value is more than one byte
long, the bytes are transmitted from the most significant to the least significant.
The MWRDY signal is used as follows:
1.
Active (0) MWRDY signals the host controller that the last eight bits of data transferred
to/from the voice module were accepted and processed (see below).
2.
The MWRDY signal is deactivated (set to 1 by the ISD-SR3000) after 8-bits of data were
transferred to/from the ISD-SR3000. The bit is set following the falling edge of the eighth
MWCLK clock-cycle.
3.
The MWRDY signal is activated (cleared to 0) by the ISD-SR3000 when it is ready to re-
ceive the first parameter byte (if there are any parameters) and so on until the last byte
of parameters is transferred. An active MWRDY signal after the last byte of parameters
indicates that the command was parsed and (if possible) executed. If that command has
a return value, the host controller must read the value before issuing a new command.
4.
When a return value is transmitted, the MWRDY signal is deactivated after every byte,
and activated again when the ISD-SR3000 is ready to send another byte or receive a new
command.
The MWRDY signal is activated (cleared to 0) after reset, and after a protocol time-out.
The MWRQST signal is used as follows:
相關PDF資料 |
PDF描述 |
|---|---|
| ISD1100SERIES | ISD1110/ISD1112 Part2 |
| ISD1200SERIES | ISD1210/ISD1212 Part3 |
| ISD1400_1 | |
| ISD1400_2 | |
| ISD1400_3 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISD-T266SA/J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| ISD-T266SA/Q | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| ISD-T266SC/J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| ISD-T266SC/Q | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
| ISD-T266SP/J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Solid-State Recorder |
發布緊急采購，3分鐘左右您將得到回復。