參數資料
型號： HYB39S64160AT-10
廠商： SIEMENS A G
元件分類： DRAM
英文描述： 64 MBit Synchronous DRAM
中文描述： 4M X 16 SYNCHRONOUS DRAM, 7 ns, PDSO54
封裝： 0.400 INCH, TSOP-54
文件頁數： 13/53頁
文件大小： 418K
代理商： HYB39S64160AT-10
HYB 39S64400/800/160BT(L)
64-MBit Synchronous DRAM
Data Book
13
12.99
command is necessary. A minimum
t
RC
time is required between two automatic refreshes in a burst
refresh mode. The same rule applies to any access command after the automatic refresh operation.
The chip has an on-chip timer and the Self Refresh mode is available. It enters the mode when RAS,
CAS, and CKE are low and WE is high at a clock timing. All of external control signals including the
clock are disabled. Returning CKE to high enables the clock and initiates the refresh exit operation.
After the exit command, at least one
t
RC
delay is required prior to any access command.
DQM Function
DQM has two functions for data I/O read and write operations. During reads, when it turns to “high”
at a clock timing, data outputs are disabled and become high impedance after two clock delay (DQM
Data Disable Latency
t
DQZ
). It also provides a data mask function for writes. When DQM is activated,
the write operation at the next clock is prohibited (DQM Write Mask Latency
t
DQW
= zero clocks).
Suspend Mode
During normal access mode, CKE is held high enabling the clock. When CKE is low, it freezes the
internal clock and extends data read and write operations. One clock delay is required for mode
entry and exit (Clock Suspend Latency
t
CSL
).
Power Down
In order to reduce standby power consumption, a power down mode is available. All banks must be
precharged and the necessary Precharge delay (
t
RP
) must occur before the SDRAM can enter the
Power Down mode. Once the Power Down mode is initiated by holding CKE low, all of the receiver
circuits except CLK and CKE are gated off. The Power Down mode does not perform any refresh
operations, therefore the device can’t remain in Power Down mode longer than the Refresh period
(
t
REF
) of the device. Exit from this mode is performed by taking CKE “high”. One clock delay is
required for mode entry and exit.
Auto Precharge
Two methods are available to precharge SDRAMs. In an automatic precharge mode, the CAS
timing accepts one extra address, CA10, to determine whether the chip restores or not after the
operation. If CA10 is high when a Read Command is issued, the
Read with Auto-Precharge
function is initiated. If CA10 is high when a Write Command is issued, the
Write with Auto-
Precharge
function is initiated. The SDRAM automatically enters the precharge operation two
clocks after the last data in.
Precharge Command
There is also a separate precharge command available. When RAS and WE are low and CAS is
high at a clock timing, it triggers the precharge operation. Three address bits, BA0, BA1 and A10 are
used to define banks as shown in the following list. The precharge command can be imposed one
clock before the last data out for CAS latency = 2 and two clocks before the last data out for CAS
latency = 3. Writes require a time delay
t
WR
from the last data out to apply the precharge command.
相關PDF資料
PDF描述
HYB39S64800 64 MBit Synchronous DRAM
HYB41256 Wirewound Inductor; Inductor Type:Standard; Inductance:10nH; Inductance Tolerance:+/- 5 %; Current Rating:400mA; Series:CM160808; Package/Case:0603; Core Material:Alumina Ceramic; Leaded Process Compatible:No RoHS Compliant: No
HYB41256-10 262,144 BIT DYNAMIC RAM
HYB41256-12 262,144 BIT DYNAMIC RAM
HYB41256-15 262,144 BIT DYNAMIC RAM
相關代理商/技術參數
參數描述
HYB39S64160AT-5.5 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 SDRAM
HYB39S64160AT-6 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 SDRAM
HYB39S64160AT-7 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 SDRAM
HYB39S64160AT-7.5 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x16 SDRAM
HYB39S64160AT-8 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:64 MBit Synchronous DRAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*