- 您現在的位置：買賣IC網 > PDF目錄385404 > HT82K96A (Holtek Semiconductor Inc.) USB Multimedia Keyboard Encoder 8-Bit Mask MCU PDF資料下載
參數資料
| 型號： | HT82K96A |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | USB Multimedia Keyboard Encoder 8-Bit Mask MCU |
| 中文描述： | 的USB多媒體鍵盤編碼器8位微控制器面膜 |
| 文件頁數： | 7/46頁 |
| 文件大?。?/td> | 298K |
| 代理商： | HT82K96A |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
HT82K96A
Rev. 1.50
7
August 25, 2006
Program Memory
ROM
The program memory is used to store the program in-
structions which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
4096 15bits,addressedbytheprogramcounterandta-
ble pointer.
Certain locations in the program memory are reserved
for special usage:
Location 000H
This area is reserved for program initialization. After
chip reset, the program always begins execution at lo-
cation 000H.
Location 004H
This area is reserved for the USB interrupt service
program. If the USB interrupt is activated, the interrupt
isenabledandthestackisnotfull,theprogrambegins
execution at location 004H.
Location 008H
ThisareaisreservedfortheTimer/EventCounter0in-
terrupt service program. If a timer interrupt results
from a Timer/Event Counter 0 overflow, and if the in-
terrupt is enabled and the stack is not full, the program
begins execution at location 008H.
Location 00CH
This location is reserved for the Timer/Event Counter
1 interrupt service program. If a timer interrupt results
from a Timer/Event Counter 1 overflow, and the inter-
rupt is enabled and the stack is not full, the program
begins execution at location 00CH.
Table location
Any location in the program memory can be used as
look-up tables. The instructions TABRDC [m] (the
current page, one page=256 words) and TABRDL
[m]
lower-order byte to the specified data memory, and
the higher-order byte to TBLH (08H). Only the desti-
nation of the lower-order byte in the table is
well-defined, the other bits of the table word are trans-
ferred to the lower portion of TBLH, and the remaining
(the last page) transfer the contents of the
1-bit words are read as 0 . The Table Higher-order
byte register (TBLH) is read only. The table pointer
(TBLP) is a read/write register (07H), which indicates
the table location. Before accessing the table, the lo-
cation must be placed in the TBLP. The TBLH is read
only and cannot be restored. If the main routine and
the ISR (Interrupt Service Routine) both employ the
table read instruction, the contents of the TBLH in the
main routine are likely to be changed by the table read
instruction used in the ISR. Errors can occur. In other
words, using the table read instruction in the main rou-
tine and the ISR simultaneously should be avoided.
However, if the table read instruction has to be applied
in both the main routine and the ISR, the interrupt is
supposed to be disabled prior to the table read in-
struction. It will not be enabled until the TBLH has
been backed up. All table related instructions require
two cycles to complete the operation. These areas
may function as normal program memory depending
upon the requirements.
Stack Register
STACK
This is a special part of the memory which is used to
save the contents of the program counter only. The
stack is organized into 8 levels and is neither part of the
data nor part of the program space, and is neither read-
able nor writeable. The activated level is indexed by the
stack pointer (SP) and is neither readable nor writeable.
0 (
!
: : : 2
: : 2
3
(
, @
(
/ (
(
)
3
(
(
(
(
#
> 6
(
, ( ; 0 1 ( A
" ! <
#
> 6
(
, ( ; 0 1 ( A
" ! <
B ( (
! ( %
( (
( :
2
2
8 2
* 2
2
)
3
(
(
(
(
Program Memory
Instruction
Table Location
*11
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P11
P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note: *11~*0: Table location bits
P11~P8: Current program counter bits
@7~@0: Table pointer bits
相關PDF資料 |
PDF描述 |
|---|---|
| HT82K96E | 8-Bit USB Multimedia Keyboard Encoder OTP MCU |
| HT82M21A | 3-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M22 | 5-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M22A | 5-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M23C | 3/5-Key USB+PS/2 Optical Mouse Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82K96E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit USB Multimedia Keyboard Encoder OTP MCU |
| HT82K96E_07 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Multimedia Keyboard Encoder 8-Bit OTP MCU |
| HT82M13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Mouse/Trackball Controller |
| HT82M21A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:3-Key 3D USB+PS/2 Optical Mouse Controller |
| HT82M21A_05 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:3-Key 3D USB+PS/2 Optical Mouse Controller |
發布緊急采購，3分鐘左右您將得到回復。