- 您現在的位置：買賣IC網 > PDF目錄385399 > HT48C50- (Holtek Semiconductor Inc.) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | HT48C50- |
| 廠商： | Holtek Semiconductor Inc. |
| 元件分類： | 數學處理器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 20/45頁 |
| 文件大?。?/td> | 295K |
| 代理商： | HT48C50- |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
HT48C50-1
20
June 14, 2000
Preliminary
cur at the same time). When the timer/event
counter 0/1 (reading TMR0/TMR1) is read, the
clock will be blocked to avoid errors. As clock
blocking may results in a counting error, this
mustbetakenintoconsiderationbytheprogram-
mer.
The bit0~bit2 of the TMR0C can be used to de-
fine the pre-scaling stages of the internal clock
sources of timer/event counter 0. The defini-
tions are as shown. The overflow signal of
timer/event counter 0 can be used to generate
PFD signals for buzzer driving.
Input/output ports
There are 35 bidirectional input/output lines in
the microcontroller, labeled from PA to PD and
PG, which are mapped to the data memory of
[12H], [14H], [16H], [18H] and [1EH] respec-
tively. All of these I/O ports can be used for input
andoutputoperations.Forinputoperation,these
portsarenon-latching,thatis,theinputsmustbe
ready at the T2 rising edge of instruction "MOV
A,[m]" (m=12H, 14H, 16H, 18H or 1EH). For out-
putoperation,allthedataislatchedandremains
unchanged until the output latch is rewritten.
Each I/O line has its own control register (PAC,
PBC, PCC, PDC, PGC) to control the input/out-
put configuration. With this control register,
CMOS output or schmitt trigger input with or
without pull-high resistor structures can be re-
configured dynamically (i.e. on-the-fly) under
software control. To function as an input, the
corresponding latch of the control register must
write "1". The input source also depends on the
control register. If the control register bit is "1",
the input will read the pad state. If the control
register bit is "0", the contents of the latches
will move to the internal bus. The latter is pos-
sible in the "read-modify-write" instruction.
For output function, CMOS is the only configu-
ration. These control registers are mapped to
locations 13H, 15H, 17H, 19H and 1FH.
* ,
# ' ! )
!
' * !
3 * / # !
#@ ! * !
' * #!
!* /
'
@
! *! !
+
= * " ! #
3 * / # !
#@ ! * !
6
( 8
( B * / & !
/
Timer/event counter 1
Label (TMR1C)
Bits
Function
0~2
Unused bit, read as"0"
TE
3
To define the TMR1 active edge of timer/event counter 1
(0=active on low to high; 1=active on high to low)
TON
4
To enable/disable timer 1 counting
(0=disabled; 1=enabled)
5
Unused bit, read as"0"
TM0
TM1
6
7
To define the operating mode
01=Event count mode (external clock)
10=Timer mode (internal clock)
11=Pulse width measurement mode
00=Unused
TMR1C register
相關PDF資料 |
PDF描述 |
|---|---|
| HT48C70-1 | I/O Type 8-Bit MCU |
| HT48R70A-1 | I/O Type 8-Bit MCU |
| HT48C70 | 8-Bit Microcontroller Series |
| HT48CA0-2 | Remote Type 8-Bit MCU |
| HT48RA0 | Remote Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT48C50(28SKDIP-H) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| HT48C50(40DIP-A) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| HT48C50-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit I/O Type Mask MCU |
| HT48C50-1_09 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type 8-Bit MCU |
| HT48C70 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Microcontroller Series |
發布緊急采購，3分鐘左右您將得到回復。