- 您現在的位置：買賣IC網 > PDF目錄385399 > HT46R47 (Holtek Semiconductor Inc.) 8-Bit OTP Battery Charger Controller PDF資料下載
參數資料
| 型號： | HT46R47 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit OTP Battery Charger Controller |
| 中文描述： | 8位檢察官電池充電器控制器 |
| 文件頁數： | 17/45頁 |
| 文件大?。?/td> | 588K |
| 代理商： | HT46R47 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
HT46R47
Rev. 1.40
17
July 18, 2001
The TM0, TM1 bits define the operating mode.
The event count mode is used to count external
events, which means the clock source comes from
an external (TMR) pin. The timer mode functions
as a normal timer with the clock source coming
fromthef
INT
clock.Thepulsewidthmeasurement
modecanbeusedtocountthehighorlowleveldu-
ration of the external signal (TMR). The counting
is based on the f
INT
.
In the event count or timer mode, once the
timer/event counter starts counting, it will count
from the current contents in the timer/event
counter to FFH. Once overflow occurs, the coun-
ter is reloaded from the timer/event counter
preload register and generates the interrupt re-
quest flag (TF; bit 5 of INTC) at the same time.
In the pulse width measurement mode with
the TON and TE bits equal to one, once the
TMR has received a transient from low to high
(or high to low if the TE bits is 0 ) it will start
counting until the TMR returns to the original
level and resets the TON. The measured result
will remain in the timer/event counter even if
the activated transient occurs again. In other
words, only one cycle measurement can be
done. Until setting the TON, the cycle measure-
ment will function again as long as it receives
further transient pulse. Note that, in this oper-
ating mode, the timer/event counter starts
counting not according to the logic level but ac-
cording to the transient edges. In the case of
counter overflows, the counter is reloaded from
the timer/event counter preload register and is-
sues the interrupt request just like the other
two modes. To enable the counting operation,
the timer ON bit (TON; bit 4 of TMRC) should
be set to 1. In the pulse width measurement
mode,theTONwillbeclearedautomaticallyaf-
ter the measurement cycle is completed. But in
the other two modes the TON can only be reset
by instructions. The overflow of the timer/event
counter is one of the wake-up sources. No mat-
ter what the operation mode is, writing a 0 to
ETI can disable the interrupt service.
In the case of timer/event counter OFF condi-
tion, writing data to the timer/event counter
preload register will also reload that data to
the timer/event counter. But if the timer/event
counter is turned on, data written to it will only
be kept in the timer/event counter preload reg-
ister. The timer/event counter will still operate
until overflow occurs. When the timer/event
counter (reading TMR) is read, the clock will be
blocked to avoid errors. As clock blocking may re-
sults in a counting error, this must be taken into
consideration by the programmer.
The bit0~bit2 of the TMRC can be used to de-
fine the pre-scaling stages of the internal clock
sources of timer/event counter. The definitions
are as shown. The overflow signal of
timer/event counter can be used to generate the
PFD signal. The timer prescaler is also used as
the PWM counter.
Input/output ports
There are 13 bidirectional input/output lines in
the microcontroller, labeled as PA, PB and PD,
which are mapped to the data memory of [12H],
[14H] and [18H] respectively. All of these I/O
ports can be used for input and output opera-
tions. For input operation, these ports are
non-latching, that is, the inputs must be ready at
the T2 rising edge of instruction MOV A,[m]
(m=12H, 14H or 18H). For output operation, all
the data is latched and remains unchanged until
the output latch is rewritten.
Each I/O line has its own control register (PAC,
PBC, PDC) to control the input/output configu-
ration. With this control register, CMOS output
or Schmitt trigger input with or without
pull-high resistor structures can be reconfig-
ured dynamically (i.e. on-the-fly) under soft-
ware control. To function as an input, the
corresponding latch of the control register must
write 1 . The input source also depends on the
control register. If the control register bit is 1 ,
the input will read the pad state. If the control
register bit is 0 , the contents of the latches
will move to the internal bus. The latter is pos-
sible in the read-modify-write instruction.
For output function, CMOS is the only configu-
ration. These control registers are mapped to
locations 13H, 15H and 19H.
After a chip reset, these input/output lines re-
main at high levels or floating state (dependent
相關PDF資料 |
PDF描述 |
|---|---|
| HT46R65-100 | A/D with LCD Type 8-Bit MCU |
| HT46C65 | A/D with LCD Type 8-Bit MCU |
| HT46C65-100 | A/D with LCD Type 8-Bit MCU |
| HT46C65-52 | A/D with LCD Type 8-Bit MCU |
| HT46C65-56 | A/D with LCD Type 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT46R47(18DIP-A) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| HT46R47(18SOP-A) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| HT46R47E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit MCU |
| HT46R47-H | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit OTP MCU |
| HT46R48 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:Cost-Effective A/D Type 8-Bit OTP MCU |
發布緊急采購，3分鐘左右您將得到回復。