- 您現在的位置：買賣IC網 > PDF目錄385396 > HSP50110 (Intersil Corporation) Digital Quadrature Tuner(數字調諧器) PDF資料下載
參數資料
| 型號： | HSP50110 |
| 廠商： | Intersil Corporation |
| 英文描述： | Digital Quadrature Tuner(數字調諧器) |
| 中文描述： | 數字正交調諧器（數字調諧器） |
| 文件頁數： | 10/24頁 |
| 文件大小： | 207K |
| 代理商： | HSP50110 |
3-10
To create the alias profile, a composite response, the
components of which are shown in the ”D” portion of
Figure 12, is made from the sum of all the alias elements.
The primary use of an alias profile is used to determine what
bandwidth yields the desired suppression of unwanted
signals for a particular application.
Reviewing Figures 9 through 11, note the following
observations:
1. The uncompensated I&D (1st order CIC) filter yields
about 12dB of alias suppression at f
S
/16R. This usable
bandwidth is considerably narrower than the 3dB filter
bandwidth. The I&D filter is the matched filter for square
wave data that has not been bandlimited.
2. The compensated I&D filter offers a flatter, wider band-
width than just the I&D alone. This filter compensates for
the frequency roll off due to the A/D converter.
3. The uncompensated 3rd order CIC filter yields over 60dB
of alias suppression at f
S
/16R. Typical application is
found in tuners, where the DQT is followed by a very nar-
row band filter.
4. The 3rd order CIC with compensation yields alias sup-
pression comparable to the 3rd order CIC, but with the
flatter, wider passband. This filter is selected for most
SATCOM applications.
Which filter is selected, is dependent on the application. It is
important to utilize these alias responses in calculating the
filter to be used, so that the signal suppression prediction will
accurately reflect the digital filter performance.
Noise Equivalent Bandwidth
The noise equivalent bandwidth (B
N
) performance of the
channel filter is dependent on the combination of Decimation
Filter and Compensation Filter chosen. For configurations
using the Integrate and Dump filter, B
N
is constant
regardless of decimation rate. However, for configurations
which use the third order CIC filter, B
N
converges to a
constant for decimation factors of over ~50. A summary of
equivalent IF B
N
’s for different filter configurations and
decimation rates is given in Table 3. These noise bandwidths
are provided so that output SNR can be calculated from input
SNR. In detection applications this bandwidth indicates the
detection bandwidth.
Re-Sampler
The Re-Sampler sets the output sample rate by controlling
the sample rate of the decimation filters (see Low Pass Filter
Section). The output sample rate may be fixed or adjusted
dynamically to synchronize with baseband waveforms. The
reduction in sample rate between the Low Pass Filter input
and output represents the decimation factor.
The Decimating filter output is sampled by the programmable
divider shown in Figure 13. The divider is a counter which is
decremented each time it is clocked. When the divider reaches
its terminal count, the output of the decimating filter is sampled.
The divider may be programmed with a divisor of from 1 to
4096 (see Table 10 Decimating Filter Configuration Register).
One of two internal clock sources are chosen for the divider
based on whether a fixed or adjustable sample rate is
desired. For fixed output sample rates, a clock equal to the
input sample rate is selected (see Decimating Filter
Configuration Table 10). For adjustable output sample rates,
a clock generated by the carry out from the Re-Sampler
NCO is chosen.
FIGURE 12.
f
S
2R
f
S
f
S
2
A
B
C
D
TABLE 3. DOUBLE SIDED NOISE EQUIVALENT BANDWIDTH
FOR DIFFERENT FILTER CONFIGURATIONS AND
OUTPUT SAMPLE RATES
DEC
INTEGRATE/
DUMP
INTEGRATE/
DUMP W/
x/sin(x)
3RD
ORDER
CIC
3RD
ORDER
CIC W/
[x/sin(x)]
3
2
1.0000
1.3775
0.6250
1.3937
10
1.0000
1.3775
0.5525
1.0785
18
1.0000
1.3775
0.5508
1.0714
26
1.0000
1.3775
0.5504
1.0698
34
1.0000
1.3775
0.5502
1.0691
42
1.0000
1.3775
0.5501
1.0688
50
1.0000
1.3775
0.5501
1.0687
58
1.0000
1.3775
0.5501
1.0686
66
1.0000
1.3775
0.5501
1.0685
74
1.0000
1.3775
0.5500
1.0684
82
1.0000
1.3775
0.5500
1.0684
90
1.0000
1.3775
0.5500
1.0684
98
1.0000
1.3775
0.5500
1.0684
106
1.0000
1.3775
0.5500
1.0684
114
1.0000
1.3775
0.5500
1.0683
122-
4096
1.0000
1.3775
0.5500
1.0683
HSP50110
相關PDF資料 |
PDF描述 |
|---|---|
| HSP50210 | Digital Costas Loop(數字Costas鎖相環) |
| HSP50214VC | Programmable Downconverter |
| HSP50214VI | Programmable Downconverter |
| HSP50214 | Programmable Downconverter |
| HSP50215VC | Digital UpConverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSP50110_01 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digital Quadrature Tuner |
| HSP50110JC-52 | 功能描述:調諧器 DIGITAL QUADRATURE TUNER 84 PLCC,52MHZ,COMM RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| HSP50110JC-52Z | 功能描述:調諧器 W/ANNEAL DIGTL TUNER 84 PLCC 52MHZ RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| HSP50110JC-60 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Tuner Circuit |
| HSP50110JI-52 | 功能描述:調諧器 DIGITAL QUADRATURE TUNER 84 PLCC,52MHZ,INDUSTRIAL RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。