- 您現在的位置：買賣IC網 > PDF目錄384443 > HSC-INTERFACEBOARD (Analog Devices, Inc.) 1.75 MSPS, 4 mW 10-Bit/12-Bit Parallel ADCs PDF資料下載
參數資料
| 型號： | HSC-INTERFACEBOARD |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 1.75 MSPS, 4 mW 10-Bit/12-Bit Parallel ADCs |
| 中文描述： | 1.75 MSPS的，4 10-Bit/12-Bit并行模數轉換器毫瓦 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 197K |
| 代理商： | HSC-INTERFACEBOARD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁
REV. A
AD7470/AD7472
–
14
–
GROUNDING AND LAYOUT
The analog and digital power supplies are independent and
separately pinned out to minimize coupling between analog and
digital sections within the device. To complement the excellent
noise performance of the AD7470/AD7472 it is imperative that
care be given to the PCB layout. Figure 25 shows a recom-
mended connection diagram for the AD7470/AD7472.
All of the AD7470/AD7472 ground pins should be soldered
directly to a ground plane to minimize series inductance. The
AV
DD
, DV
DD
and V
DRIVE
pins should be decoupled to both the
analog and digital ground planes. The large value capacitors will
decouple low frequency noise to analog ground, the small value
capacitors will decouple high frequency noise to digital ground.
All digital circuitry power pins should be decoupled to the digi-
tal ground plane. The use of ground planes can physically sepa-
rate sensitive analog components from the noisy digital system.
The two ground planes should
be joined in
only
one place and
should not overlap so as to minimize capacitive coupling be-
tween them. If the AD7470/AD7472 is in a system where
multiple devices require AGND to DGND connections, the
connection should still be made at one point only, a star ground
point, which should be established as close as possible to the
AD7470/AD7472.
Noise can be minimized by applying some simple rules to the
PCB layout: analog signals should be kept away from digital
signals; fast switching signals like clocks should be shielded with
digital ground to avoid radiating noise to other sections of the
board and clock signals should never be run near the analog
inputs; avoid running digital lines under the device as these will
couple noise onto the die; the power supply lines to the AD7470/
AD7472 should use as large a trace as possible to provide a low
impedance path and reduce the effects of glitches on the power
supply line; avoid crossover of digital and analog signals and
place traces that are on opposite sides of the board at right angles
to each other.
Noise to the analog power line can be further reduced by use of
multiple decoupling capacitors as shown in Figure 25. Decou-
pling capacitors should be placed directly at the power inlet to
the PCB and also as close as possible to the power pins of the
AD7470/AD7472. The same decoupling method should be
used on other ICs on the PCB, with the capacitor leads as short
as possible to minimize lead inductance.
POWER SUPPLIES
Separate power supplies for AV
DD
and DV
DD
are desirable but if
necessary DV
DD
may share its power connection to AV
DD
. The
digital supply (DV
DD
) must not exceed the analog supply (AV
DD
)
by more than 0.3 V in normal operation.
MICROPROCESSOR INTERFACING
AD7470/AD7472 to ADSP-2185 Interface
Figure 26 shows a typical interface between the AD7470/AD7472
and the ADSP-2185. The ADSP-2185 processor can be used in
one of two memory modes, Full Memory Mode and Host Mode.
The Mode C pin determines in which mode the processor works.
The interface in Figure 26 is set up to have the processor work-
ing in Full Memory Mode, which allows full external addressing
capabilities.
When the AD7470/AD7472 has finished converting, the BUSY
line requests an interrupt through the
IRQ2
pin. The
IRQ2
interrupt has to be set up in the interrupt control register as
edge-sensitive. The DMS (Data Memory Select) pin latches in
the address of the A/D into the address decoder. The read op-
eration is thus started.
ADDRESS
DECODER
AD7470/
AD7472*
ADSP-2185*
A0
–
A15
DMS
IRQ2
RD
MODE C
D0
–
D23
CONVST
CS
RD
BUSY
DB0
–
DB9
(DB11)
ADDRESS BUS
DATA BUS
100k
*ADDITIONAL PINS OMITTED FOR CLARITY
OPTIONAL
Figure 26. Interfacing to the ADSP-2185
AD7470/AD7472 to ADSP-21065 Interface
Figure 27 shows a typical interface between the AD7470/AD7472
and the ADSP-21065L SHARC
processor. This interface is an
example of one of three DMA handshake modes. The
MS
X
AD7470/
AD7472
AD780
10 F
+
1nF
V
IN
V
OUT
1nF
+
10 F
0.1 F
10 F
DV
DD
AGND
DGND
V
DRIVE
VREF
AV
DD
+
0.1 F
47 F
ANALOG
SUPPLY
+5V
+
0.1 F
Figure 25. Decoupling Circuit
SHARC is a registered trademark of Analog Devices, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| HSML-A431-X90M1 | Surface Mount LED Indicator |
| HSMV-A430-Y90M1 | Surface Mount LED Indicator |
| HSMX-A43X-XXXXX | Surface Mount LED Indicator |
| HSMA-A430-W90M1 | Surface Mount LED Indicator |
| HSMA-A431-X90M1 | Surface Mount LED Indicator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSCJ-HRFCJ-A(40) | 功能描述:光纖連接器 FIBER OPTIC CONN RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HSCJ-HRFCJ-B | 功能描述:CONN ADAPT SC/FC PNL MNT RoHS:否 類別:連接器，互連式 >> 光纖 - 適配器 系列:HSC 產品變化通告:Product Obsolescence Notification 01/Apri/2010 標準包裝:500 系列:- 類型:耦合器 轉換源（適配器端）:POF 插座 轉換到（適配器端）:POF 插座 單工/雙工:單工 模式:- 安裝類型:面板安裝，悶頭 環箍材料:- 特點:- 顏色:藍 其它名稱:516-1891HFBR-4515-NDQ2114296B |
| HSCJ-HRFCJ-B(40) | 功能描述:光纖連接器 ADAPT SC/FC PNL MNT RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HSCJ-HRFCJ-B(43) | 功能描述:光纖連接器 CONV ADAPTER RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HSCJ-HRFCJ-B(51) | 制造商:HRS 制造商全稱:HRS 功能描述:FC Type Fiber Optic Connectors |
發布緊急采購，3分鐘左右您將得到回復。