參數資料
型號： GM2125
廠商： Electronic Theatre Controls, Inc.
英文描述： ANALOG INTER FACE XGA/SXGA ONPANEL LCD PANEL CONTROLLER
中文描述： 模擬國際米蘭的XGA / SXGA ONPANEL液晶顯示器控制器
文件頁數： 45/54頁
文件大?。?/td> 1339K
代理商： GM2125
***
Genesis Microchip Confidential ***
gm2115/25 Preliminary Data Sheet
June 2002
43
C2115-DAT-01B
Pin Name
GPIO0/PWM0
GPIO1/PWM1
GPIO2/PWM2
GPIO3/TIMER1
GPIO4/UART_DI
GPIO5/UARD_D0
GPIO6
GPIO7
GPIO8/IRQINn
GPIO9/TCON_ROE2
GPIO10/TCON_ROE3
GPIO11/ROM_WEn
GPIO12/NVRAM_SDA
GPIO13/NVRAM_SCL
GPIO14/DDC_SCL
GPIO15/DDC_SDA
GPIO16/HFSn
GPIO17
GPIO18
GPIO19
GPIO20
GPIO21/IRQn
GPIO22/HCLK
Pin Number
40
41
42
43
44
45
46
47
39
48
49
50
51
52
6
7
205
1
208
207
206
4
204
Alternate function
PWM0, PWM1 and PWM2 back light intensity controls, as described in section 4.16.2 below.
Timer1 input of the OCM.
OCM UART data in/out signals respectively.
Horizontal timing signals in the TCON column driver interface.
OCM external interrupt source (IRQINn).
Row output enables ROE2 and ROE3 in the TCON row driver interface.
Write enable for external ROM if programmable FLASH device is used.
Data and clock lines for master 2-wire serial interface to NVRAM when gm2115/25 is used in
standalone configuration (section Figure 25).
General-purpose input/output signals. Open drain option via register setting.
[Bi-directional Input, Schmitt trigger (400mV typical hysteresis), 5V-tolerant]
Serial data line for 2-wire host interface.
No alternative function.
OCM interrupt output pin.
Serial input clock for 2-wire host interface.
Table 15. gm2115/25 GPIOs and Alternate Functions
4
4
.
.
1
1
4
4
B
B
o
o
o
o
t
t
s
s
t
t
r
r
a
a
p
p
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
a
a
t
t
i
i
o
o
n
n
P
P
i
i
n
n
s
s
During hardware reset, the external ROM address pins ROM_ADDR[15:0] are configured as
inputs. On the negating edge of RESETn, the value on these pins is latched and stored. This
value is readable by the on-chip microcontroller (or an external microcontroller via the host
interface). Install a 10K pull-up resistor to indicate a ‘1’, otherwise a ‘0’ is indicated.
Signal Name
Pin Name
Description
HOST_ADDR(4:0)
USER_BITS(4:0)
ROM_ADDR(4:0)
If using 2-wire host protocol, these are bits 4:0 of the serial bus device address.
Otherwise, these settings are available for reading from a status register but are otherwise unused by the
gm2115/25. Used for “soft” configuration settings.
If using 2-wire host protocol, this is bit 5 of serial the bus device address.
Otherwise, program this bit to 0.
If using 2-wire host protocol, this is bit 6 of the serial bus device address.
Otherwise, program this bit to 0.
Program this bit to 0 for 2-wire host protocol operation.
Program this bit to 0 for 2-wire host protocol operation.
Determines the operating condition of the OCM after HW reset:
0 = OCM remains in reset until enabled by register bit.
1 = OCM becomes active after OCM_CLK is stable.
These settings are available for reading from a status register but are otherwise unused by the gm2115/25.
Selects reference clock source:
0 = XTAL and TCLK pins are connected to a crystal oscillator (see Figure 4).
1 = TCLK input is driven with a single-ended TTL/CMOS clock oscillator (see Figure 7).
Together with OCM_CONTROL register (0x22) bit 4, this bit selects internal/external ROM configuration.
0 = All 48K of ROM is internal.
1 = All 48K of ROM is in external ROM using ROM_ADDR15:0 address outputs if
register 0x22 bit 4 is 0. If register 0x22 bit 4 is 1, 0-32K ROM is internal, and
32K~48K ROM is external using ROM_ADDR13:0 address outputs.
HOST_ADDR(5)
ROM_ADDR5
HOST_ADDR(6)
ROM_ADDR6
HOST_PROTOCOL
HOST_PORT_EN
OCM_START
ROM_ADDR7
ROM_ADDR8
ROM_ADDR9
USER_BITS(7:5)
OSC_SEL
ROM_ADDR(12:10)
ROM_ADDR13
OCM_ROM_CNFG(1)
ROM_ADDR14
Table 16. Bootstrap Signals
相關PDF資料
PDF描述
GM2116 ANALOG-INTERFACE ONPANEL XGA LCD CONTROLLER WITH RSDS TRANSMITTER
GM2121 SXGA LCD Monitor Controller with Integrated Analog Interface and Dual LVDS Transmitter
GM317 3- TERMINAL ADJUSTABLE REGULATOR
GM317TA3R 3- TERMINAL ADJUSTABLE REGULATOR
GM317TA3T 3- TERMINAL ADJUSTABLE REGULATOR
相關代理商/技術參數
參數描述
GM2126 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ANALOG INTERFACE ONPANEL SXGA LCD CONTROLLER WITH RSDS TRANSMITTER
GM215 制造商:GECKODRIVE 功能描述:CONTROLLER STEPPER MOTOR 13W 制造商:GECKODRIVE 功能描述:CONTROLLER, STEPPER MOTOR, 13W, No. of Phases:(Not Available), SVHC:No SVHC (20-
GM216 NJ BLACK 制造商:Hirschmann Electronics GmbH & Co Kg 功能描述:CONNECTOR SOLENOID
GM216 NJ GREY 制造商:Hirschmann Electronics GmbH & Co Kg 功能描述:CONNECTOR SOLENOID
GM21CG270J50NT 制造商:Cal-Chip Electronics 功能描述:GM21CG270J50NT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*