- 您現在的位置：買賣IC網 > PDF目錄1922 > FT245RL-REEL (FTDI, Future Technology Devices International Ltd)IC USB TO PARALLEL FIFO 28-SSOP PDF資料下載
參數資料
| 型號： | FT245RL-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 17/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB TO PARALLEL FIFO 28-SSOP |
| 產品培訓模塊： | USB Introduction |
| 標準包裝： | 1 |
| 應用： | USB 至 FIFO 控制器 |
| 接口： | USB，F(xiàn)IFO，（同步/異步） |
| 電源電壓： | 1.8 V ~ 5.25 V |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 產品目錄頁面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1020-ND - MOD USB PARALLEL FIFO DEV FT245R |
| 其它名稱： | 768-1011-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Copyright 2010 Future Technology Devices International Limited
24
Document No.: FT_000052
FT245R USB FIFO IC Datasheet Version 2.12
Clearance No.: FTDI# 39
7.3 USB Bus Powered with Power Switching Configuration
FT245R
A
G
N
D
G
N
D
G
N
D
G
N
D
T
E
S
T
100nF
3V3OUT
VCCIO
NC
RESET#
NC
+
100nF
10nF
5V VCC
D0
D1
D2
D3
D4
D5
D6
D7
TXE#
WR#
RD#
RXF#
USBDP
USBDM
VCC
1
2
3
4
5
OSCI
OSCO
PWREN#
Ferrite
Bead
+
4.7uF
SHIELD
GND
0.1uF
1k
Soft Start
Circuit
d
g
s
Switched 5V Power
to External Logic
5V VCC
P-Channel Power
MOSFET
10K
5V VCC
Figure 7.3 Bus Powered with Power Switching Configuration
A requirement of USB bus powered applications, is when in USB suspend mode the application draws a
total current of less than 2.5mA. This requirement includes external logic. Some external logic has the
ability to power itself down into a low current state by monitoring the PWREN# signal. For external logic
that cannot power itself down in this way, the FT245R provides a simple but effective method of turning
off power during the USB suspend mode.
Figure 7.3 shows an example of using a discrete P-Channel MOSFET to control the power to external
logic. A suitable device to do this is an International Rectifier (www.irf.com) IRLML6402, or equivalent. It
is recommended that a “soft start” circuit consisting of a 1kΩ series resistor and a 0.1μF capacitor is used
to limit the current surge when the MOSFET turns on. Without the soft start circuit it is possible that the
transient power surge, caused when the MOSFET switches on, will reset the FT245R or the USB host/hub
controller. The soft start circuit example shown in Figure 7.3 powers up with a slew rate of
approximaely12.5V/ms. Thus supply voltage to external logic transitions from GND to +5V in
approximately 400 microseconds.
As an alternative to the MOSFET, a dedicated power switch IC with inbuilt “soft-start” can be used. A
suitable power switch IC for such an application is the Micrel (www.micrel.com) MIC2025-2BM or
equivalent.
With power switching controlled designs the following should be noted:
i) The external logic to which the power is being switched should have its own reset circuitry to
automatically reset the logic when power is re-applied when moving out of suspend mode.
ii) Set the Pull-down on Suspend option in the internal FT245R EEPROM.
iii) The PWREN# pin should be used to switch the power to the external circuitry.
iv) For USB high-power bus powered applications (one that consumes greater than 100mA, and up
to 500mA of current from the USB bus), the power consumption of the application must be set in
the Max Power field in the internal FT245R EEPROM. A high-power bus powered application uses
the descriptor in the internal FT245R EEPROM to inform the system of its power requirements.
相關PDF資料 |
PDF描述 |
|---|---|
| FT4232HQ-REEL | IC USB HS QUAD UART/SYNC 64-QFN |
| FUSB1500MHX | IC USB 2.0 TRANSCEIVER 16-MLP |
| FUSB2805MLX | TXRX USB2.0 HS OTG ULPI 32MLP |
| FXLA2203UMX | TRANSLATOR LEVEL DUAL 24UMLP |
| GAL16V8D-15LJN | SPLD 62.5MHZ EECMOS 20 PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT245RL-TUBE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB FIFO IC 28-Pin SSOP Tube |
| FT245RQ | 制造商:Future Technology Devices International 功能描述:Single Chip USB 32-Pin QFN 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC USB TO FIFO SMD QFN-32 245 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC, USB TO FIFO, SMD, QFN-32, 245 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Full Speed to Parallel FIFO IC, Includes Oscillator and EEPROM - QFN-32 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC, USB FIFO INTERFACE, QFN-32; USB Type:USB FIFO; USB Version:2.0; Supply Voltage Min:1.8V; Supply Voltage Max:5.25V; Digital IC Case Style:QFN; No. of Pins:32; Data Rate:1Mbps; No. of Ports:2; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| FT245RQ-6000 | 制造商:FTDI 制造商全稱:FTDI 功能描述:USB FIFO IC - Single chip USB to parallel FIFO bidirectional data transfer interface |
| FT245RQ-REEL | 功能描述:USB 接口集成電路 USB to Parallel FIFO Enhanced IC QFN-32 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT245RQ-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:Single Chip USB Tray |
發布緊急采購，3分鐘左右您將得到回復。