- 您現在的位置：買賣IC網 > PDF目錄382960 > flas00xx (SIEMENS AG) MultiMediaCard(多媒體卡) PDF資料下載
參數資料
| 型號： | flas00xx |
| 廠商： | SIEMENS AG |
| 英文描述： | MultiMediaCard(多媒體卡) |
| 中文描述： | 多媒體卡（多媒體卡） |
| 文件頁數： | 32/79頁 |
| 文件大?。?/td> | 516K |
| 代理商： | FLAS00XX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
MultiMediaCard Flash
Preliminary MultiMediaCard Product Manual;
1998 SANDISK CORPORATION
Page 32 of 79
Table 4-6 Status Register
Bits
Type
Value
Description
Clear
Cond.
31
E R
‘0’= no error
‘1’= error
The commands argument was out of allowed range for this card.
C
30
E R
X ‘0’= no error
‘1’= error
A misaligned address, which did not match the block length was used
in the command.
C
29
E R
‘0’= no error
‘1’= error
The transferred block length is not allowed for this card or the number
of bytes transferred does not match the block length
C
28
E R
‘0’= no error
‘1’= error
An error in the sequence of erase commands occurred.
C
27
E X
‘0’= no error
‘1’= error
An invalid selection, sectors or groups, for erase.
C
26
E R X
‘0’= not
protected
‘1’= protected
The command tried to write a write protected block.
C
25-24
Reserved
23
E R
‘0’= no error
‘1’= error
The CRC check of the previous command failed.
B
22
E R
‘0’= no error
‘1’= error
Command not legal for the current state
B
21
E X
‘0’=
‘1’= failure
success
Card internal ECC was applied but the correction of data is failed.
C
20
E R X
‘0’= no error
‘1’= error
Internal card controller error
C
19
E R X
‘0’= no error
‘1’= error
A general or an unknown error occurred during the operation.
C
18
E X
‘0’= no error
‘1’= error
The card could not sustain data transfer in stream read mode
C
17
E X
‘0’= no error
‘1’= error
The card could not sustain data programming in stream write mode
C
16
E R
‘0’= no error
‘1’= error
Can be one of the following errors:
-The CID register has been already written and cannot be overwritten
-The read only section of the CSD does not match the card content.
-An attempt to reverse the copy (set as original) or permanent WP
(unprotected) bits was made.
C
15
S X
‘0’=not
protected
protected
‘1’=
Only partial address space was erased due to existing WP blocks.
C
14
S X
‘0’=
‘1’= disabled
enabled
The command is done without using the internal ECC.
A
13
S R
‘0’= cleared ‘1’=
set
An erase sequence was cleared before executing because an out of
erase sequence command was received
C
12-9
S X
0=idle
1=ready
2=ident
3=stby
4=tran
5=data
6=rcv
7=prg
8=dis
Current state of the card.
B
相關PDF資料 |
PDF描述 |
|---|---|
| FLC-453232-R56M | FLC-453232-R56M |
| FLEX405 | Fire Alarm Control Panel with built-in DACT and remote-site upload/download capability |
| FLI2300 | DIGITAL VIDEO FORMAT CONVERTER |
| FLI8532 | Single-Chip LCD TV Controller |
| FLI8538 | Single-Chip Enhanced LCD TV Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FLASH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flash Memory Brochure |
| FLASH CARD-128 | 功能描述:存儲卡 128 MEG FLASH CARD RoHS:否 制造商:Olimex Ltd. 產品:SD 存儲容量: 連續讀取: 連續寫入: 有源模式電流: 工作電源電壓: 最大工作溫度: 尺寸: |
| FLASH CARD-512 | 功能描述:存儲卡 512 MB COMPACT FLASH CARD RoHS:否 制造商:Olimex Ltd. 產品:SD 存儲容量: 連續讀取: 連續寫入: 有源模式電流: 工作電源電壓: 最大工作溫度: 尺寸: |
| FLASH PRO 4 | 制造商:Microsemi Corporation 功能描述: |
| FLASH-150Z | 制造商:Amprobe Test Tools 功能描述:FLASHLIGHT - 2 AA BATTERIES W/ ZOOM ;ROHS COMPLIANT: NA |
發布緊急采購，3分鐘左右您將得到回復。