- 您現在的位置：買賣IC網 > PDF目錄1917 > DSPB56366AG120 (Freescale Semiconductor)IC DSP 24BIT AUD 120MHZ 144-LQFP PDF資料下載
參數資料
| 型號： | DSPB56366AG120 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 22/110頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP 24BIT AUD 120MHZ 144-LQFP |
| 產品變化通告： | Product Discontinuation 24/Feb/2012 |
| 標準包裝： | 60 |
| 系列： | DSP56K/Symphony |
| 類型： | 音頻處理器 |
| 接口： | 主機接口，I²C，SAI，SPI |
| 時鐘速率： | 120MHz |
| 非易失內存： | ROM（240 kB） |
| 芯片上RAM： | 69kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 3.30V |
| 工作溫度： | -40°C ~ 110°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁
DSP56366 Technical Data, Rev. 3.1
Freescale Semiconductor
2-15
FST
Input or output
GPIO
disconnected
Frame Sync for Transmitter—This is the transmitter frame sync input/output
signal. For synchronous mode, this signal is the frame sync for both
transmitters and receivers. For asynchronous mode, FST is the frame sync for
the transmitters only. The direction is determined by the transmitter frame
sync direction (TFSD) bit in the ESAI transmit clock control register (TCCR).
PC4
Input, output, or
disconnected
Port C 4—When the ESAI is configured as GPIO, this signal is individually
programmable as input, output, or internally disconnected.
The default state after reset is GPIO disconnected.
This input is 5 V tolerant.
SCKR
Input or output
GPIO
disconnected
Receiver Serial Clock—SCKR provides the receiver serial bit clock for the
ESAI. The SCKR operates as a clock input or output used by all the enabled
receivers in the asynchronous mode (SYN=0), or as serial flag 0 pin in the
synchronous mode (SYN=1).
When this pin is configured as serial flag pin, its direction is determined by the
RCKD bit in the RCCR register. When configured as the output flag OF0, this
pin will reflect the value of the OF0 bit in the SAICR register, and the data in
the OF0 bit will show up at the pin synchronized to the frame sync in normal
mode or the slot in network mode. When configured as the input flag IF0, the
data value at the pin will be stored in the IF0 bit in the SAISR register,
synchronized by the frame sync in normal mode or the slot in network mode.
PC0
Input, output, or
disconnected
GPIO
disconnected
Port C 0—When the ESAI is configured as GPIO, this signal is individually
programmable as input, output, or internally disconnected.
The default state after reset is GPIO disconnected.
This input is 5 V tolerant.
SCKT
Input or output
GPIO
disconnected
Transmitter Serial Clock—This signal provides the serial bit rate clock for the
ESAI. SCKT is a clock input or output used by all enabled transmitters and
receivers in synchronous mode, or by all enabled transmitters in
asynchronous mode.
PC3
Input, output, or
disconnected
GPIO
disconnected
Port C 3—When the ESAI is configured as GPIO, this signal is individually
programmable as input, output, or internally disconnected.
The default state after reset is GPIO disconnected.
This input is 5 V tolerant.
SDO5
Output
GPIO
disconnected
Serial Data Output 5—When programmed as a transmitter, SDO5 is used to
transmit data from the TX5 serial transmit shift register.
SDI0
Input
GPIO
disconnected
Serial Data Input 0—When programmed as a receiver, SDI0 is used to
receive serial data into the RX0 serial receive shift register.
Table 2-11 Enhanced Serial Audio Interface Signals (continued)
Signal
Name
Signal Type
State during
Reset
Signal Description
相關PDF資料 |
PDF描述 |
|---|---|
| DSPB56367AG150 | IC DSP 24BIT 150MHZ 144-LQFP |
| DSPB56371AF180 | IC DSP 24BIT 180MHZ 80-LQFP |
| DSPB56374AEC | IC DSP 24BIT 150MHZ 52-LQFP |
| DSPB56720CAG | DSP 24BIT AUD 200MHZ 144-LQFP |
| DSPB56724AG | DSP 24BIT AUD 250MHZ 144-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPB56366PV120 | 制造商:Motorola Inc 功能描述: 制造商:Freescale Semiconductor 功能描述:IC 制造商:MOTOROLA 功能描述: |
| DSPB56367AG150 | 功能描述:數字信號處理器和控制器 - DSP, DSC 150Mhz/150MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPB56367PV150 | 功能描述:數字信號處理器和控制器 - DSP, DSC 150Mhz/ 150MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPB5636AG120 | 制造商:Freescale Semiconductor 功能描述: |
| DSPB56371AF150 | 功能描述:數字信號處理器和控制器 - DSP, DSC 150 MHZ VERSION DSPB371 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。