參數資料
型號： DS21448LN+
廠商： Maxim Integrated Products
文件頁數： 27/60頁
文件大?。?/td> 0K
描述： IC LIU QUAD E1/T1/J1 128-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 72
類型： 線路接口裝置（LIU）
驅動器/接收器數： 4/4
規程： T1/E1/J1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-LQFP（14x20）
包裝： 管件
DS21448 3.3V T1/E1/J1 Quad Line Interface
33 of 60
7. ANALOG INTERFACE
7.1 Receiver
The DS21448 contains a digital clock recovery system. The DS21448 couples to the receive E1 or T1 twisted pair
(or coaxial cable in 75
E1 applications) through a 1:1 transformer. See Table 7-C for transformer details.
Figure 7-1, Figure 7-2, Figure 7-3, and Table 4-L show the receive termination requirements. The DS21448 has the
option of using internal termination resistors.
The DS21448 is designed to be fully software selectable for E1 and T1 without the need to change any external
resistors for the receive side. The receive side allows user configuration for 75
, 100, or 120 receive
termination by setting the RT1 (CCR5.1) and RT0 (CCR5.0) bits. When using the internal termination feature, the
Rr resistors should be 60 each. See Figure 7-1 for details. If external termination is required, RT1 and RT0 should
be set to 0, and both Rr resistors (Figure 7-1) should be 37.5, 50, or 60 each, depending on the line
impedance.
The resultant E1 or T1 clock derived from the 2.048/1.544 PLL (JACLK in Figure 1-1) is internally multiplied by 16
through another internal PLL and fed to the clock recovery system. The clock recovery system uses the clock from
the PLL circuit to form a 16-times oversampler used to recover the clock and data. This oversampling technique
offers outstanding performance to meet jitter tolerance specifications, as shown in Figure 7-7.
Normally, the clock that is output at the RCLK pin is the recovered clock from the E1 AMI/HDB3 or T1 AMI/B8ZS
waveform presented at the RTIP and RRING inputs. When no signal is present at RTIP and RRING, an RCL
condition occurs, and the RCLK is derived from the JACLK source. See Figure 1-1 for more details. If the jitter
attenuator is placed in the receive path (as is the case in most applications), the jitter attenuator restores the RCLK
to an approximate 50% duty cycle. If the jitter attenuator is either placed in the transmit path or is disabled, the
RCLK output can exhibit slightly shorter high cycles of the clock. This is because of the highly oversampled digital
clock recovery circuitry. See the receive-side AC timing characteristics in Section 10 for more details.
The receive-side circuitry also contains a clock synthesizer that outputs a user-configurable clock (up to
16.384MHz) synthesized from RCLK at BPCLK (pin 31). See Table 4-J for details about output clock frequencies at
BPCLK. In hardware mode, BPCLK defaults to a 16.384MHz output.
The DS21448 has a bypass mode for the receive-side clock and data. This allows the BPCLK to be derived from
RCLK after the jitter attenuator, while the clock and data presented at RCLK, RPOS, and RNEG go unaltered. This
is intended for applications where the receive-side jitter attenuation is done after the LIU. Setting RJAB (CCR6.3) to
logic 1 enables the bypass. Ensure the jitter attenuator is in the receive path (CCR4.3 = 0). See Figure 1-1 for more
details.
The DS21448 reports the signal strength at RTIP and RRING in 2.5dB increments through RL3–RL0 located in the
receive information register 2. This feature is helpful when troubleshooting line performance problems (Table 5-B).
E1 and T1 monitor applications require various flat-gain settings for the receive-side circuitry. The DS21448 can be
programmed to support these applications through the monitor mode control bits MM1 and MM0. When the monitor
modes are enabled, the receiver tolerates normal line loss up to -6dB (Table 4-K).
7.2 Transmitter
The DS21448 uses a set of laser-trimmed delay lines with a precision digital-to-analog converter (DAC) to create
the waveforms that are transmitted onto the E1 or T1 line. The waveforms meet the latest ETSI, ITU, ANSI, and
AT&T specifications. The user selects which waveform to generate by setting the ETS bit (CCR1.7) for E1 or T1
operation, then programming the L2/L1/L0 bits in common control register 4 for the appropriate application. See
Table 7-A and Table 7-B for the proper L2/L1/L0 settings.
A 2.048MHz or 1.544MHz TTL clock is required at TCLK for transmitting data at TPOS and TNEG. ITU
specification G.703 requires ±50ppm accuracy for T1 and E1. TR62411 and ANSI specs require ±32ppm accuracy
for T1 interfaces. The clock can be sourced internally by RCLK or JACLK. See CCR1.2, CCR1.1, CCR1.0, and
Figure 1-3 for details. Because of the transmitter’s design, very little jitter (less than 0.005UIP-P broadband from
相關PDF資料
PDF描述
NB7VPQ16MMNHTBG IC CML DVR PRE-EMPH 1CH 16-QFN
MAX1112CPP+ IC ADC 8BIT LP 20-DIP
MS27474T22B21SC CONN RCPT 21POS JAM NUT W/SCKT
MAX1110EPP+ IC ADC 8BIT LP 20-DIP
MS27468T23A35SB CONN RCPT 100POS JAM NUT W/SCKT
相關代理商/技術參數
參數描述
DS21448LN+ 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448-LW 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21448N 功能描述:網絡控制器與處理器 IC 3.3V E1/T1/J1 Quad Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2145 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
DS21455 功能描述:網絡控制器與處理器 IC Quad E1-T1-J1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*