- 您現在的位置：買賣IC網 > PDF目錄17034 > CWMPCEVB5200BE (Freescale Semiconductor)BOARD MPC5200B W/256MB PDF資料下載
參數資料
| 型號： | CWMPCEVB5200BE |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 26/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD MPC5200B W/256MB |
| 標準包裝： | 1 |
| 類型： | MPU |
| 適用于相關產品： | MPC5200B |
| 所含物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
MPC5200B Data Sheet, Rev. 4
32
Freescale Semiconductor
NOTES:
1 tUI, tMLI, tLI indicate sender-to-recipient or recipient-to-sender interlocks. That is, one agent (sender or recipient) is waiting for
the other agent to respond with a signal before proceeding.
tUI is an unlimited interlock that has no maximum time value.
tMLI is a limited time-out that has a defined minimum.
tLI is a limited time-out that has a defined maximum.
2 All timing parameters are measured at the connector of the drive to which the parameter applies. For example, the sender shall
stop generating STROBE edges tRFS after negation of DMARDY. STROBE and DMARDY timing measurements are taken at
the connector of the sender. Even though the sender stops generating STROBE edges, the receiver may receive additional
STROBE edges due to propagation delays. All timing measurement switching points (low to high and high to low) are taken at
1.5 V.
t AZ
—
10
—
10
—
10
Maximum time allowed for output drivers to release
from being asserted or negated
A8.36
tZAH
20
—
20
—
20
—
Minimum delay time required for output drivers to
assert or negate from released state
A8.37
t ZAD
0—0—0—
A8.38
t ENV
20
70
20
70
20
70
Envelope time—from DMACK to STOP and
HDMARDY during data out burst initiation.
A8.39
t SR
—
50
—
30
—
20
STROBE to DMARDY time, if DMARDY is negated
before this long after STROBE edge, the recipient
receives no more than one additional data word.
A8.40
t RFS
—
75
—
60
—
50
Ready-to-Final STROBE time—no STROBE edges
are sent this long after negation of DMARDY.
A8.41
t RP
160
—
125
—
100
—
Ready-to-Pause time—the time recipient waits to
initiate pause after negating DMARDY.
A8.42
t IORDYZ
—
20
—
20
—
20
Pull-up time before allowing IORDY to be released.
A8.43
t ZIORDY
0
—
0
—
0
—
Minimum time drive waits before driving IORDY
A8.44
t ACK
20
—
20
—
20
—
Setup and hold times for DMACK, before assertion or
negation.
A8.45
t SS
50
—
50
—
50
—
Time from STROBE edge to negation of DMARQ or
assertion of STOP, when sender terminates a burst.
A8.46
Table 29. Ultra DMA Timing Specification (continued)
Sym
MODE 0
(ns)
MODE 1
(ns)
MODE 2
(ns)
Comment
SpecID
Min
Max
Min
Max
Min
Max
相關PDF資料 |
PDF描述 |
|---|---|
| 0210490246 | CABLE JUMPER 1.25MM .178M 18POS |
| 0210490245 | CABLE JUMPER 1.25MM .178M 18POS |
| 0210390953 | CABLE JUMPER 1MM .152M 25POS |
| RBC08DRYI-S734 | CONN EDGECARD 16POS DIP .100 SLD |
| LGU2E471MELA | CAP ALUM 470UF 250V 20% SNAP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CWMPCEVB5200BE | 制造商:Freescale Semiconductor 功能描述:MPC5200B BOARD W/ 256MB |
| CWMPH1 | 功能描述:電線導管 In-Cabinet Horizontal Cable Manager Fron RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| CWMPH1Y | 制造商:Panduit Corp 功能描述:PANDUIT |
| CWMPHF1 | 功能描述:電線導管 In-Cabinet Horizontal Cable Manager Fron RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| CWMPV2318 | 功能描述:電線導管 In-Cabinet Vertical Cable Manager 18 RU RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
發(fā)布緊急采購，3分鐘左右您將得到回復。