參數資料
型號： COPCSH984XXX/WM
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDSO28
封裝： SOIC-28
文件頁數： 4/60頁
文件大小： 693K
代理商： COPCSH984XXX/WM
AC Electrical Characteristics 68xCS and 68xxG:
55C
≤ T
A ≤ +125C unless otherwise specified
Parameter
Conditions
Min
Typ
Max
Units
Instruction Cycle Time (t
c)
Crystal, Resonator
V
CC ≥ 4.5V
1.0
DC
s
R/C Oscillator
68xCS & 68xEG only)
V
CC ≥ 4.5V
3.0
DC
s
Inputs
t
SETUP
V
CC ≥ 4.5V
200
ns
t
HOLD
V
CC ≥ 4.5V
60
ns
Output Propagation Delay
R
L = 2.2k, CL = 100 pF
t
PD1,tPD0
SO, SK
V
CC ≥ 4.5V
0.7
s
All Others
V
CC ≥ 4.5V
1
s
MICROWIRE Setup Time (t
UWS) (Note 10)
20
ns
MICROWIRE Hold Time (t
UWH) (Note 10)
56
ns
MICROWIRE Output Propagation Delay (t
UPD)
220
ns
Input Pulse Width (Note 11)
Interrupt Input High Time
1
t
c
Interrupt Input Low Time
1
t
c
Timer 1, 2, 3 Input High Time
1
t
c
Timer 1, 2, 3 Input Low Time
1
t
c
Reset Pulse Width
1
s
Note 6: Maximum rate of voltage change must be less than 0.5 V/ms.
Note 7: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 8: The HALT mode will stop CKI from oscillating in the RC and the Crystal configurations. Measurement of IDD HALT is done with device neither sourcing or
sinking current; with L, C, and G0–G5 programmed as low outputs and not driving a load; all outputs programmed low and not driving a load; all inputs tied to VCC;
clock monitor and comparators disabled. Parameter refers to HALT mode entered via setting bit 7 of the G Port data register. Part will pull up CKI during HALT in crys-
tal clock mode.
Note 9: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than VCC and the pins will have sink current
to VCC when biased at voltages greater than VCC (the pins do not have source current when biased at a voltage below VCC). The effective resistance to VCC is 750
(typical). These two pins will not latch up. The voltage at the pins must be limited to less than 14V. WARNING: Voltages in excess of 14V will cause damage to the
pins. This warning excludes ESD transients.
Note 10: Parameter characterized but not tested.
Note 11: tc = Instruction Cycle Time
Comparators AC and DC Characteristics
V
CC = 5V, 40C ≤ TA ≤ +85C.
Parameter
Conditions
Min
Typ
Max
Units
Input Offset Voltage
0.4V
≤ V
IN ≤ VCC 1.5V
±10
±25
mV
Input Common Mode Voltage Range
0.4
V
CC 1.5
V
Voltage Gain
300k
V/V
Low Level Output Current
V
OL = 0.4V
1.6
mA
High Level Output Current
V
OH = 4.6V
1.6
mA
DC Supply Current per Comparator (When Enabled)
250
A
Response Time
100 mV Overdrive,
1
s
100 pF Load
COP888xG/CS
Family
www.national.com
12
相關PDF資料
PDF描述
CP-8-D-2-TS1-TP INTERCONNECTION DEVICE
CP2-SAB1100#NAME TWO PART BOARD CONNECTOR
CP2-SAB1250#NAME TWO PART BOARD CONNECTOR
CP2-SAB950#NAME TWO PART BOARD CONNECTOR
CP20420CPGA155B-0C FPGA, 4200 GATES, CPGA155
相關代理商/技術參數
參數描述
COPEG884-AQC/WM/SP110451 功能描述:IC MCU 8BIT 制造商:texas instruments 系列:* 零件狀態:最後搶購 標準包裝:1
COPEG884-AVW/WM 制造商:Texas Instruments 功能描述:
COPEG884-CHP/WM/E7001546 制造商:Texas Instruments 功能描述:
COPEG888 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit Microcontroller with UART and Three Multi-Function Timers
COPH-030 制造商:edco liebert 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*