參數資料
型號： COP8SBR9KMT8
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 微控制器/微處理器
英文描述： 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
中文描述： 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO56
封裝： TSSOP-56
文件頁數： 24/80頁
文件大?。?/td> 972K
代理商： COP8SBR9KMT8
10.0 Functional Description
(Continued)
10.8 OSCILLATOR CIRCUITS
The device has two crystal oscillators to facilitate low power
operation while maintaining throughput when required. Fur-
ther information on the use of the two oscillators is found in
Section 7.0 Power Saving Features. The low speed oscillator
utilizes the L0 and L1 port pins. References in the following
text to CKI will also apply to L0 and references to G7/CKO
will also apply to L1.
10.8.1 Oscillator
CKI is the clock input while G7/CKO is the clock generator
output to the crystal. An on-chip bias resistor connected
between CKI and CKO is provided to reduce system part
count. The value of the resistor is in the range of 0.5M to 2M
(typically 1.0M).
Table 2
shows the component values re-
quired for various standard crystal values. Resistor R2 is
on-chip, for the high speed oscillator, and is shown for
reference.
Figure 12
shows the crystal oscillator connection
diagram. A ceramic resonator of the required frequency may
be used in place of a crystal if the accuracy requirements are
not quite as strict.
TABLE 2. Crystal Oscillator Configuration,
T
A
= 25C, V
CC
= 5V
R1 (k
)
R2 (M
)
C1 (pF)
C2 (pF)
CKI Freq.
(MHz)
10
5
1
0.455
32.768
kHz
*
0
0
0
On Chip
On Chip
On Chip
On Chip
20
18
18
18
18
18–36
100
**
18–36
100–156
**
5.6
0
*
Applies to connection to low speed oscillator on port pins L0 and L1 only.
**
See Note below.
The crystal and other oscillator components should be
placed in close proximity to the CKI and CKO pins to mini-
mize printed circuit trace length.
The values for the external capacitors should be chosen to
obtain the manufacturer’s specified load capacitance for the
crystal when combined with the parasitic capacitance of the
trace, socket, and package (which can vary from 0 to 8 pF).
The guideline in choosing these capacitors is:
Manufacturer’s specified load cap = (C
1
* C
2
) / (C
1
+ C
2
) +
C
parasitic
C
can be trimmed to obtain the desired frequency. C
2
should be less than or equal to C
1
.
Note
: The low power design of the low speed oscillator
makes it extremely sensitive to board layout and load ca-
pacitance. The user should place the crystal and load ca-
pacitors within 1cm. of the device and must ensure that the
above equation for load capacitance is strictly followed. If
these conditions are not met, the application may have
problems with startup of the low speed oscillator.
TABLE 3. Startup Times
CKI Frequency
10 MHz
3.33 MHz
1 MHz
455 kHz
32 kHz (low speed oscillator)
Startup Time
1–10 ms
3–10 ms
3–20 ms
10–30 ms
2–5 sec
10.8.2 Clock Doubler
This device contains a frequency doubler that doubles the
frequency of the oscillator selected to operate the main
microcontroller core. The details of how to select either the
high speed oscillator or low speed oscillator are described in,
Power Saving Features. When the high speed oscillator
connected to CKI operates at 10 MHz, the internal clock
frequency is 20 MHz, resulting in an instruction cycle time of
0.5 μs. When the 32 kHz oscillator connected to L0 and L1 is
selected, the internal clock frequency is 64 kHz, resulting in
an instruction cycle of 152.6 μs. The output of the clock
doubler is called MCLK and is referenced in many places
within this document.
10138914
FIGURE 11. Reset Circuit Using Power-On Reset
C
www.national.com
24
相關PDF資料
PDF描述
COP8SCR9KMT8 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8SDR9KMTA8 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8SCR9IMT7 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8SDR9IMT7 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
COP8SBR9IMT8 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout
相關代理商/技術參數
參數描述
COP8SBR9LVA8 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8SBR9LVA8/NOPB 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8SBR9LVA8NOPB 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 3.3V/5V 68-Pin PLCC Rail
COP8SCE9 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
COP8SCE9HLQ7 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM and Brownout Reset
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*