參數資料
型號： CDP1020
廠商： INTERSIL CORP
元件分類： 總線控制器
英文描述： SMBus/I2C ACPI Dual Device Bay Controller
中文描述： I2C BUS CONTROLLER, PDSO28
封裝： PLASTIC, MS-013AE, SOIC-28
文件頁數： 18/23頁
文件大?。?/td> 154K
代理商： CDP1020
2-435
REMREQ_EN bit is set. This event will transition the bay into
the Removal Requested state, flash the bay status LED
amber, and assert the ALRT pin to notify the OS.
The Device Removal Requested state is also entered when
the OS writes a %011 to the BAY_STREQ field in the BCERx.
In either case, the CDP1020 will enter the Device Removal
Requested state only if a device is inserted into the bay
(1394PRx & USBPRx = 0).
While in this state the bay status LED will flash amber at 1Hz.
Device Removal Allowed
The Device Removal Allowed state is the last of the five bay
states. This state can only be entered through an OS write to
the BCERx register. The CDP1020 hardware cannot
transition the bay state into Device Removal Allowed.
The CDP1020 will transition the bay state controller to the
Device Removal Allowed state when the OS writes a %100
to the BAY_STREQ field of the BCERx register. The
CDP1020 will enter this state if and only if there is a device
detected in the bay (1394PRx & USBPRx = 0).
The Device Removal Allowed state is defined as the last state
that a device is in before being removed by a user. All bay
controls, including PWREN outputs and solenoid control
through the LOCK_CTL bit, are available in this state. Typically,
though, a device in the Removal Allowed state will be disabled
with its V
ID
supply off. From this state the OS may transition the
CDP1020 state controller into any other state (except for Bay
Empty, of course) by simply writing to the BAY_STREQ bits in
the BCER. Also, removal request events will be generated if the
REMREQ_EN bit is set and a user asserts the REMREQ input.
Finally, when in the Removal Allowed state, the CDP1020
will NOT generate a removal event if the device is removed
from the bay and the REMEVTWAK bit is clear. This allows
the OS to not be disturbed by the removal of a device that
has already been powered down. If the REMEVTWAK flag is
set, the CDP1020 will generate a removal event when a
device is removed (assuming the DEVSTSCHG_EN bit is
set). In any case, the CDP1020 will always transition the bay
state to Bay Empty upon the removal of a device, regardless
of the state of any of the control or status bits.
In the Device Removal Allowed state, the bay status LED
(LEDGx and LEDAx) outputs will be off.
State Transitions
The following tables illustrate the hardware (CDP1020
controlled) and software (OS controlled) state transitions for
the CDP1020 bay state controllers.
TABLE 2. HARDWARE EVENT BAY STATE TRANSITION TABLE
CURRENT
STATE
NEXT STATE
HARDWARE EVENT
CONDITIONS
NOTES
----
Bay Empty
(no device present)
Power-On Reset
Establish initial state.
----
Bay Empty
(device present)
Power-On Reset
A device occupying a bay at power-on time will not
necessarily cause DEVSTSCHG to be set.
Furthermore, since DEVSTSCHG_EN defaults to ‘0’
no bay state transition will result. Either the system
BIOS or the OS, upon loading, will automatically
enumerate all occupied bays and MUST clear
DEVSTSCHG if it was set.
Device
Inserted
Bay Empty
Device removed from
the bay.
Present bit(s) has
transitioned from 1 to 0
independentofthestate
of DEVSTSCHG_EN.
Unexpected user behavior. The device was removed
prior to being properly enabled by the OS. In this case
the software controlled interlock mechanism may have
been overridden.
Device
Enabled
Removal
Requested
User pressed the
hardware removal
request button, if
present
REMREQ_STS and
REMREQ_EN are both
set.
User requested device removal through the hardware
removal request button.
Removal
Requested
Bay Empty
Device removed from
the bay.
Present bit(s) has
transitioned from 1 to 0
independentofthestate
of DEVSTSCHG_EN.
Unexpected user behavior. The device was removed
prior to completion of the proper removal request
sequence.Inthiscasethesoftwarecontrolledinterlock
mechanism may have been overridden.
Device
Removal
Allowed
Bay Empty
Device was removed
from the bay
Present bit(s) has
transitioned from 1 to 0
independentofthestate
of DEVSTSCHG_EN.
Completion of normal device removal sequence.
CDP1020
相關PDF資料
PDF描述
CDP1802AC High-Reliability CMOS 8-Bit Microprocessor
CDP1802AC3 High-Reliability CMOS 8-Bit Microprocessor
CDP1802ACD CMOS 8-Bit Microprocessors
CDP1802ACDX CMOS 8-Bit Microprocessors
CDP1802ACE CMOS 8-Bit Microprocessors
相關代理商/技術參數
參數描述
CDP1020M 制造商:Rochester Electronics LLC 功能描述:- Bulk
CDP1020M WAF 制造商:Intersil Corporation 功能描述:
CD-P12 制造商:SMC Corporation of America 功能描述:SWITCH PROTECTOR 24VDC
CDP1582EX 制造商:Rochester Electronics LLC 功能描述:- Bulk
CDP1802A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 8-Bit Microprocessors
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*