參數資料
型號： C8051F300DK
廠商： Silicon Laboratories Inc
文件頁數： 23/178頁
文件大?。?/td> 0K
描述： DEV KIT F300/301/302/303/304/305
標準包裝： 1
類型： MCU
適用于相關產品： Silicon Laboratories C8051 F300/001/002
所含物品： 評估板，電源，USB 線纜，適配器和文檔
產品目錄頁面： 626 (CN2011-ZH PDF)
相關產品： 336-1535-5-ND - IC 8051 MCU 8K FLASH 14-SOIC
C8051F300-GMR-ND - IC 8051 MCU 8K FLASH 11QFN
C8051F002-GQR-ND - IC 8051 MCU 32K FLASH 32LQFP
C8051F001-GQR-ND - IC 8051 MCU 32K FLASH 48TQFP
336-1245-ND - IC 8051 MCU 8K FLASH 11QFN
336-1186-ND - IC 8051 MCU 32K FLASH 32LQFP
336-1185-ND - IC 8051 MCU 32K FLASH 48TQFP
其它名稱： 336-1246
Rev. 2.9
119
C8051F300/1/2/3/4/5
13.4.2. SMB0CN Control Register
SMB0CN is used to control the interface and to provide status information (see SFR Definition 13.2). The
higher four bits of SMB0CN (MASTER, TXMODE, STA, and STO) form a status vector that can be used to
jump to service routines. MASTER and TXMODE indicate the master/slave state and transmit/receive
modes, respectively.
The STA bit indicates that a START has been detected or generated since the last SMBus interrupt. When
set to ‘1’, the STA bit will cause the SMBus to enter Master mode and generate a START when the bus
becomes free. STA is not cleared by hardware after the START is generated; it must be cleared by soft-
ware.
As a master, writing the STO bit will cause the hardware to generate a STOP condition and end the current
transfer after the next ACK cycle. STO is cleared by hardware after the STOP condition is generated. As a
slave, STO indicates that a STOP condition has been detected since the last SMBus interrupt. STO is also
used in slave mode to manage the transition from slave receiver to slave transmitter; see Section 13.5.4
for details on this procedure.
If STO and STA are both set to ‘1’ (while in Master Mode), a STOP followed by a START will be generated.
As a receiver, writing the ACK bit defines the outgoing ACK value; as a transmitter, reading the ACK bit
indicates the value received on the last ACK cycle. ACKRQ is set each time a byte is received, indicating
that an outgoing ACK value is needed. When ACKRQ is set, software should write the desired outgoing
value to the ACK bit before clearing SI. A NACK will be generated if software does not write the ACK bit
before clearing SI. SDA will reflect the defined ACK value immediately following a write to the ACK bit;
however SCL will remain low until SI is cleared. If a received slave address is not acknowledged, further
slave events will be ignored until the next START is detected.
The ARBLOST bit indicates that the interface has lost an arbitration. This may occur anytime the interface
is transmitting (master or slave). A lost arbitration while operating as a slave indicates a bus error condi-
tion. ARBLOST is cleared by hardware each time SI is cleared.
The SI bit (SMBus Interrupt Flag) is set at the beginning and end of each transfer, after each byte frame, or
when an arbitration is lost; see Table 13.3 for more details.
Important Note About the SI Bit: The SMBus interface is stalled while SI is set; thus SCL is held low, and
the bus is stalled until software clears SI.
Table 13.3 lists all sources for hardware changes to the SMB0CN bits. Refer to Table 13.4 for SMBus sta-
tus decoding using the SMB0CN register.
相關PDF資料
PDF描述
MIC4424YN IC DRIVER MOSFET 3A DUAL 8DIP
AIRD-03-8R2M INDUCTOR PWR DRUM CORE 8.2UH
C8051F005DK DEV KIT FOR F005/006/007
LM4040C25QDBZTG4 IC VREF SHUNT PREC 2.5V SOT-23-3
LB2016T330K INDUCTOR WOUND 33UH 85MA 0806
相關代理商/技術參數
參數描述
C8051F300DK-A 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F300DK-B 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F300DK-E 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F300DK-G 功能描述:8位微控制器 -MCU MCU DEVELOPMENT KIT W/ GLOBAL POWER SPLY RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F300DK-H 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*