參數資料
型號： C8051F300DK
廠商： Silicon Laboratories Inc
文件頁數： 158/178頁
文件大小： 0K
描述： DEV KIT F300/301/302/303/304/305
標準包裝： 1
類型： MCU
適用于相關產品： Silicon Laboratories C8051 F300/001/002
所含物品： 評估板，電源，USB 線纜，適配器和文檔
產品目錄頁面： 626 (CN2011-ZH PDF)
相關產品： 336-1535-5-ND - IC 8051 MCU 8K FLASH 14-SOIC
C8051F300-GMR-ND - IC 8051 MCU 8K FLASH 11QFN
C8051F002-GQR-ND - IC 8051 MCU 32K FLASH 32LQFP
C8051F001-GQR-ND - IC 8051 MCU 32K FLASH 48TQFP
336-1245-ND - IC 8051 MCU 8K FLASH 11QFN
336-1186-ND - IC 8051 MCU 32K FLASH 32LQFP
336-1185-ND - IC 8051 MCU 32K FLASH 48TQFP
其它名稱： 336-1246
C8051F300/1/2/3/4/5
80
Rev. 2.9
8.4.
Power Management Modes
The CIP-51 core has two software programmable power management modes: Idle and Stop. Idle mode
halts the CPU while leaving the peripherals and clocks active. In Stop mode, the CPU is halted, all inter-
rupts and timers (except the Missing Clock Detector) are inactive, and the system clock is stopped (analog
peripherals remain in their selected states). Since clocks are running in Idle mode, power consumption is
dependent upon the system clock frequency and the number of peripherals left in active mode before
entering Idle. Stop mode consumes the least power. SFR Definition 8.12 describes the Power Control Reg-
ister (PCON) used to control the CIP-51's power management modes.
Although the CIP-51 has Idle and Stop modes built in (as with any standard 8051 architecture), power
management of the entire MCU is better accomplished by enabling/disabling individual peripherals as
needed. Each analog peripheral can be disabled when not in use and placed in low power mode. Digital
peripherals, such as timers or serial buses, draw little power when they are not in use. Turning off the oscil-
lators lowers power consumption considerably; however a reset is required to restart the MCU.
8.4.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the CIP-51 to halt the CPU and enter Idle mode as soon
as the instruction that sets the bit completes execution.
All internal registers and memory maintain their
original data. All analog and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an
enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume
operation. The pending interrupt will be serviced and the next instruction to be executed after the return
from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit.
If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence
and begins program execution at address 0x0000.
If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby termi-
nate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event
of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by
software prior to entering the Idle mode if the WDT was initially configured to allow this operation. This pro-
vides the opportunity for additional power savings, allowing the system to remain in the Idle mode indefi-
nitely, waiting for an external stimulus to wake up the system. Refer to Section “16.3. Watchdog Timer
Mode” on page 164 for more information on the use and configuration of the WDT.
Note: Any instruction that sets the IDLE bit should be immediately followed by an instruction that
has 2 or more opcode bytes. For example:
// in 'C':
PCON |= 0x01;
// set IDLE bit
PCON
= PCON;
// ... followed by a 3-cycle dummy instruction
; in assembly:
ORL PCON, #01h
; set IDLE bit
MOV PCON, PCON
; ... followed by a 3-cycle dummy instruction
If the instruction following the write of the IDLE bit is a single-byte instruction and an interrupt occurs during
the execution phase of the instruction that sets the IDLE bit, the CPU may not wake from IDLE mode when
a future interrupt occurs.
相關PDF資料
PDF描述
MIC4424YN IC DRIVER MOSFET 3A DUAL 8DIP
AIRD-03-8R2M INDUCTOR PWR DRUM CORE 8.2UH
C8051F005DK DEV KIT FOR F005/006/007
LM4040C25QDBZTG4 IC VREF SHUNT PREC 2.5V SOT-23-3
LB2016T330K INDUCTOR WOUND 33UH 85MA 0806
相關代理商/技術參數
參數描述
C8051F300DK-A 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F300DK-B 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F300DK-E 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F300DK-G 功能描述:8位微控制器 -MCU MCU DEVELOPMENT KIT W/ GLOBAL POWER SPLY RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F300DK-H 功能描述:DEV KIT FOR F300/301/302/304/305 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*