參數資料
型號： C8051F006
廠商： Cygnal Technologies
英文描述： 25 MIPS,32k Flash,2.25k Ram,12bit ADC,48 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,12位 ADC,48 腳 MCU)
中文描述： 25 MIPS的，32K閃存，2.25k羊，12位ADC，48引腳微控制器（25 MIPS的，32K的閃速存儲器，2.25k羊，12位ADC和48腳微控制器）
文件頁數： 115/170頁
文件大?。?/td> 1294K
代理商： C8051F006
4.2001; Rev. 1.3
CYGNAL Integrated Products, Inc.
2001
Page 115
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
PRELIMINARY
16.2.4. Slave Receiver Mode
Serial data is received on SDA while the serial clock is received on SCL. First, a byte is received that contains an
address and data direction bit. In this case the data direction bit (R/W) will be logic 0 to indicate a “WRITE”
operation. If the received address matches the slave’s assigned address (or a general call address is received) one or
more bytes of serial data are received from the master. After each byte is received, an acknowledge bit is transmitted
by the slave. The master outputs START and STOP conditions to indicate the beginning and end of the serial
transfer.
16.3.
Arbitration
A master may start a transfer only if the bus is free. The bus is free after a STOP condition or after the SCL and
SDA lines remains high for a specified time. Two or more master devices may attempt to generate a START
condition at the same time. Since the devices that generated the START condition may not be aware that other
masters are contending for the bus, an arbitration scheme is employed. The master devices continue to transmit until
one of the masters transmits a HIGH level, while the other(s) master transmits a LOW level on SDA. The first
master(s) transmitting the HIGH level on SDA looses the arbitration and is required to give up the bus.
16.4.
Clock Low Extension
SMBus provides a clock synchronization mechanism, similar to I2C, which allows devices with different speed
capabilities to coexist on the bus. A clock-low extension is used during a transfer in order to allow slower slave
devices to communicate with faster masters. The slave can hold the SCL line LOW to extend the clock low period,
effectively decreasing the serial clock frequency.
16.5.
Timeouts
16.5.1. SCL Low Timeout
If the SCL line is held low by a slave device on the bus, no further communication is possible. Furthermore, the
master cannot force the SCL line high to correct the error condition. To solve this problem, the SMBus protocol
specifies that devices participating in a transfer must detect any clock cycle held low longer than 25ms as a “timeout”
condition. Devices that have detected the timeout condition must reset the communication no later than 10ms after
detecting the timeout condition.
One of the MCU’s general-purpose timers, operating in 16-bit auto-reload mode, can be used to monitor the SCL
line for this timeout condition. Timer 3 is specifically designed for this purpose. (Refer to the Timer 3 Section 19.3.
for detailed information on Timer 3 operation.)
16.5.2. SCL High (SMBus Free) Timeout
The SMBus specification stipulates that if a device holds the SCL and SDA lines high for more that 50usec, the bus
is designated as free. The SMB0CR register is used to detect this condition when the FTE bit in SMB0CN is set.
16.6.
SMBus Special Function Registers
The SMBus serial interface is accessed and controlled through five SFRs: SMB0CN Control Register, SMB0CR
Clock Rate Register, SMB0ADR Address Register, SMB0DAT Data Register and SMB0STA Status Register. The
system device may have one or more SMBus serial interfaces implemented. The five special function registers
related to the operation of the SMBus interface are described in the following section.
相關PDF資料
PDF描述
C8051F007 25 MIPS,32k Flash,2.25k Ram,12bit ADC,32 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,12位 ADC,32 腳 MCU)
C8051F010 20 MIPS,32k Flash,256 Ram,10bit ADC,64 Pin MCU(20 MIPS,32k 閃速存儲器,256 Ram,10位 ADC,64 腳 MCU)
C8051F015 25 MIPS,32k Flash,2.25k Ram,10bit ADC,64 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,10位 ADC,64 腳 MCU)
C8051F016 25 MIPS,32k Flash,2.25k Ram,10bit ADC,48 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,10位 ADC,48 腳 MCU)
C8051F022 25 MIPS,64k Flash,4.25k Ram,10bit ADC,100 Pin MCU(25 MIPS,64k 閃速存儲器,4.25k Ram,10位 ADC,100 腳 MCU)
相關代理商/技術參數
參數描述
C8051F006-GQ 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F006-GQR 功能描述:8位微控制器 -MCU 32KB 12ADC 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F006R 功能描述:8位微控制器 -MCU C +-12Bit 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F007 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F007-GQ 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*