參數資料
型號： C8051F005
廠商： Cygnal Technologies
英文描述： 25 MIPS,32k Flash,2.25k Ram,12bit ADC,64 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,12位 ADC,64 腳 MCU)
中文描述： 25 MIPS的，32K閃存，2.25k羊，12位ADC，64引腳微控制器（25 MIPS的，32K的閃速存儲器，2.25k羊，12位ADC和64腳微控制器）
文件頁數： 30/170頁
文件大?。?/td> 1294K
代理商： C8051F005
Page 30
CYGNAL Integrated Products, Inc.
2001
4.2001; Rev. 1.3
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
PRELIMINARY
5.2.
The ADC uses VREF to determine its full-scale voltage, thus the reference must be properly configured before
performing a conversion (see Section 9). The ADC has a maximum conversion speed of 100ksps. The ADC
conversion clock is derived from the system clock. Conversion clock speed can be reduced by a factor of 2, 4, 8 or
16 via the ADCSC bits in the ADC0CF Register. This is useful to adjust conversion speed to accommodate different
system clock speeds.
A conversion can be initiated in one of four ways, depending on the programmed states of the ADC Start of
Conversion Mode bits (ADSTM1, ADSTM0) in ADC0CN. Conversions may be initiated by:
1. Writing a 1 to the ADBUSY bit of ADC0CN;
2. A Timer 3 overflow (i.e. timed continuous conversions);
3. A rising edge detected on the external ADC convert start signal, CNVSTR;
4. A Timer 2 overflow (i.e. timed continuous conversions).
Writing a 1 to ADBUSY provides software control of the ADC whereby conversions are performed “on-demand”.
During conversion, the ADBUSY bit is set to 1 and restored to 0 when conversion is complete. The falling edge of
ADBUSY triggers an interrupt (when enabled) and sets the interrupt flag in ADC0CN. Converted data is available
in the ADC data word MSB and LSB registers, ADC0H, ADC0L. Converted data can be either left or right justified
in the ADC0H:ADC0L register pair (see example in Figure 5.9) depending on the programmed state of the ADLJST
bit in the ADC0CN register.
The ADCTM bit in register ADC0CN controls the ADC track-and-hold mode. In its default state, the ADC input is
continuously tracked, except when a conversion is in progress. Setting ADCTM to 1 allows one of four different low
power track-and-hold modes to be specified by states of the ADSTM1-0 bits (also in ADC0CN):
1. Tracking begins with a write of 1 to ADBUSY and lasts for 3 SAR clocks;
2. Tracking starts with an overflow of Timer 3 and lasts for 3 SAR clocks;
3. Tracking is active only when the CNVSTR input is low;
4. Tracking starts with an overflow of Timer 2 and lasts for 3 SAR clocks.
Modes 1, 2 and 4 (above) are useful when the start of conversion is triggered with a software command or when the
ADC is operated continuously. Mode 3 is used when the start of conversion is triggered by external hardware. In
this case, the track-and-hold is in its low power mode at times when the CNVSTR input is high. Tracking can also
be disabled (shutdown) when the entire chip is in low power standby or sleep modes.
ADC Modes of Operation
Figure 5.2. 12-Bit ADC Track and Conversion Example Timing
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
CNVSTR
(ADSTM[1:0]=10)
ADCTM=1
Track
Convert
Low Power Mode
ADCTM=0
Track Or Convert
Convert
Track
Low Power or
Convert
Timer2, Timer3 Overflow;
Write 1 to ADBUSY
(ADSTM[1:0]=00, 01, 11)
ADCTM=1
Track
Convert
Low Power Mode
ADCTM=0
Track or Convert
Convert
Track
Low Power or
Convert
A. ADC Timing for External Trigger Source
B. ADC Timing for Internal Trigger Sources
SAR Clocks
SAR Clocks
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
SAR Clocks
相關PDF資料
PDF描述
C8051F006 25 MIPS,32k Flash,2.25k Ram,12bit ADC,48 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,12位 ADC,48 腳 MCU)
C8051F007 25 MIPS,32k Flash,2.25k Ram,12bit ADC,32 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,12位 ADC,32 腳 MCU)
C8051F010 20 MIPS,32k Flash,256 Ram,10bit ADC,64 Pin MCU(20 MIPS,32k 閃速存儲器,256 Ram,10位 ADC,64 腳 MCU)
C8051F015 25 MIPS,32k Flash,2.25k Ram,10bit ADC,64 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,10位 ADC,64 腳 MCU)
C8051F016 25 MIPS,32k Flash,2.25k Ram,10bit ADC,48 Pin MCU(25 MIPS,32k 閃速存儲器,2.25k Ram,10位 ADC,48 腳 MCU)
相關代理商/技術參數
參數描述
C8051F005/0046 制造商:Silicon Laboratories Inc 功能描述:
C8051F005DK 功能描述:開發板和工具包 - 8051 MCU DEVELOPMENT KIT W/ US POWER SUPPLY RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
C8051F005DK-A 功能描述:DEV KIT FOR C8051F005/F006/F007 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F005DK-B 功能描述:DEV KIT FOR C8051F005/F006/F007 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
C8051F005DK-E 功能描述:DEV KIT FOR C8051F005/F006/F007 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*