- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2013H (Benchmark Technology Group) Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2013H |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) |
| 中文描述： | 氣體計IC，電源輔助應用（應用于電源援助的氣體計芯片） |
| 文件頁數： | 8/24頁 |
| 文件大?。?/td> | 195K |
| 代理商： | BQ2013H |
The initial full battery capacity is 35mVh (4667mAh) until
the bq2013H “l(fā)earns” a new capacity with a qualified dis-
charge from full to EDV1.
3.
Nominal Available Capacity (NAC):
NAC counts up during charge to a maximum value
of LMD and down during discharge and self dis-
charge to 0. NAC is reset to 0 on initialization and
on the first valid charge following discharge to
EDV1. To prevent overstatement of charge during
periods of overcharge, NAC stops incrementing
when NAC = LMD. When the DONE input is as-
serted high, indicating full charge completion, NAC
is set to LMD.
4.
Discharge Count Register (DCR):
The DCR counts up during discharge independent
of NAC and could continue increasing after NAC
has decremented to 0.
Prior to NAC = 0 (empty
battery), both discharge and self-discharge incre-
ment the DCR. After NAC = 0, only discharge in-
crements the DCR. The DCR resets to 0 when NAC
= LMD.
The DCR does not roll over but stops
counting when it reaches FFFFh.
The DCR value becomes the new LMD value on the
first charge after a valid discharge to EDV1 if all of
the following conditions are met:
I
No valid charge initiations (charges greater than
2 NAC updates) occurred during the period be-
tween NAC = LMD and EDV1.
I
The self-discharge count is less than 6% of NAC.
I
The temperature is
≥
0°C when the EDV1 level
is reached during discharge.
I
VDQ is set.
Charge Counting
Charge activity is detected based on a positive voltage
on the V
input.
If charge activity is detected, the
bq2013H increments NAC at a rate proportional to V
(V
SR
+ V
) and, if enabled, activates an LED display
if V
> 500
μ
V. Charge actions increment the NAC af-
ter compensation for charge rate and temperature.
The bq2013H detects charge activity with V
> 250
μ
V.
A valid charge equates to a sustained charge activity
greater than 2 NAC updates. Once a valid charge is de-
tected, charge counting continues until V
SRO
drops be-
low 250
μ
V.
Discharge Counting
All discharge counts where V
< -250
μ
V cause the
NAC register to decrement and the DCR to increment. If
enabled, the display is activated when V
< -2mV.
The display remains active for 10 seconds after V
SRO
rises above - 2mV.
Self-Discharge Estimation
The bq2013H decrements NAC and increments DCR for
self-discharge based on time and temperature. The self-
discharge count rate is programmed per Table 3. This is
the rate for a battery temperature between 20–30°C.
The NAC register cannot be decremented below 0.
Count Compensations
The bq2013H determines fast charge when the NAC up-
dates at a rate of
≥
2 counts/s. Charge activity is com-
pensated for temperature and rate before updating
NAC. Self-discharge estimation is compensated for tem-
perature before updating NAC or DCR.
Charge Compensation
Charge efficiency factors are selected using Table 5 for
trickle charge and fast charge. Fast charge is defined as
a rate of charge resulting in
≥
2 NAC counts/s (0.16C to
0.6C,depending on PFC selections;see Table 2).
Temperature adapts the charge rate compensation
factors over three ranges between nominal, warm, and
hot temperatures. Program pin 5 is used to select one of
three compensation programs. These values are shown
in Table 5.
8
bq2013H
相關PDF資料 |
PDF描述 |
|---|---|
| bq2014H | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
| bq2014 | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2013HEVM-001 | 功能描述:電源管理IC開發工具 BQ2013H Eval Kit for NiCd 16.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2013HSN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for Power- Assist Applications |
| BQ2013HSN-A514 | 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2013HSN-A514 | 制造商:Texas Instruments 功能描述:SEMICONDUCTORS ((NS)) |
| BQ2013HSN-A514G4 | 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。