參數資料
型號： bq2013H
廠商： Benchmark Technology Group
英文描述： Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片)
中文描述： 氣體計IC，電源輔助應用（應用于電源援助的氣體計芯片）
文件頁數： 12/24頁
文件大小： 195K
代理商： BQ2013H
Primary Status Flags Register (FLGS1)
The FLGS1 register (address=01h) contains the primary
bq2013H flags.
The
charge status
flag (CHGS) is asserted when a
valid charge rate is detected. The bq2013H deems the
charge valid if it results in two NAC updates with V
> 250
μ
V. A V
SRO
of less than 250
μ
V or discharge activity
clears CHGS.
The CHGS location is:
FLGS1 Bits
7
6
5
4
3
2
1
0
CHGS
-
-
-
-
-
-
-
where CHGS is
0
Either discharge activity detected or
V
SRO
< 250
μ
V
Two NAC updates with V
SRO
> 250
μ
V
The
battery replaced
flag (BRP) is asserted whenever
the bq2013H is reset by application of V
or by a serial
port command. BRP is reset when either a valid charge
action increments NAC to be equal to LMD, or when a
valid charge action is detected after the EDV1 flag is
asserted. BRP = 1 signifies that the device has been re-
set.
1
The BRP location is:
FLGS1 Bits
7
6
5
4
3
2
1
0
-
BRP
-
-
-
-
-
-
where BRP is
0
bq2013H is charged until NAC = LMD or
on the first charge after or a discharge
which sets the EDV1 flag
1
bq2013H is reset
The
valid discharge
flag (VDQ) is asserted when the
bq2013H is discharged from NAC=LMD.
mains set until either LMD is updated or until one of
three actions that can clear VDQ occurs:
The flag re-
I
NAC has been reduced by more than 6% during
because of self-discharge since VDQ was set
I
A valid charge action sustained at V
SRO
> V
SRQ
for at
least two NAC updates
I
The EDV1 flag was set at a temperature below 0°C.
The VDQ location is:
FLGS1 Bits
7
6
5
4
3
2
1
0
-
-
-
-
VDQ
-
-
-
where VDQ is
0
Self-discharge reduces NAC by 6%, valid
charge action detected, EDV1 asserted with
the temperature less than 0
°
C, or reset
1
On first discharge after NAC = LMD
The first
end-of-discharge warning
flag (EDV1)
warns the user that the battery is empty. SEG1 blinks
at a 4Hz rate and DONE is asserted low. EDV1 detec-
tion is disabled if OVLD = 1. The EDV flag is latched
until a valid charge has been detected.
The EDV1 location is:
FLGS1 Bits
7
6
5
4
3
2
1
0
-
-
-
-
-
-
EDV1
-
where EDV1 is
0
Valid charge action detected or V
SB
≥
V
EDV1
V
< V
for the delay time, provided
that the OVLD bit is not set
1
The
final end-of-discharge warning
flag (EDVF) flag
is used to warn that battery power is at a failure condi-
tion. All segment drivers are turned off. The EDVF flag
is latched until a valid charge has been detected. The
EDVF threshold is set 100mV below the EDV1 thresh-
old.
The EDVF location is:
FLGS1 Bits
7
6
5
4
3
2
1
0
-
-
-
-
-
-
-
EDVF
Where EDVF is:
0
ValidchargeactiondetectedorV
SB
≥
V
EDVF
V
SB
< V
EDVF
, providing the OVLD bit is not
set
1
12
bq2013H
相關PDF資料
PDF描述
bq2014H Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片)
bq2014 Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）)
bq2040 Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）)
bq2050H Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片)
bq2050 Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片)
相關代理商/技術參數
參數描述
BQ2013HEVM-001 功能描述:電源管理IC開發工具 BQ2013H Eval Kit for NiCd 16.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
BQ2013HSN 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for Power- Assist Applications
BQ2013HSN-A514 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
BQ2013HSN-A514 制造商:Texas Instruments 功能描述:SEMICONDUCTORS ((NS))
BQ2013HSN-A514G4 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*