- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2013H (Benchmark Technology Group) Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2013H |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) |
| 中文描述： | 氣體計IC，電源輔助應用（應用于電源援助的氣體計芯片） |
| 文件頁數： | 3/24頁 |
| 文件大?。?/td> | 195K |
| 代理商： | BQ2013H |
Functional Description
General Operation
The bq2013H determines battery capacity by monitoring
the amount of charge input to or removed from a recharge-
able battery. The bq2013H measures discharge and charge
currents, estimates self-discharge, monitors the battery for
low-battery voltage thresholds, and compensates for tem-
perature and charge rates. The charge measurement is
made by monitoring the voltage across a small-value se-
ries sense resistor between the battery’s negative terminal
and ground. The available battery charge is determined
by monitoring this voltage over time and correcting the
measurement for the environmental and operating condi-
tions.
Figure 1 shows a typical battery pack application of the
bq2013H using the LED display.
configured to display capacity in either a relative or an
absolute display mode. The relative display mode uses
the last measured discharge capacity of the battery as
the battery “full” reference. The absolute display mode
uses the programmed full count (PFC) as the full refer-
ence, forcing each segment of the display to represent a
fixed amount of charge. A push-button display feature
is available for enabling the LED display.
The bq2013H can be
The bq2013H monitors the charge and discharge cur-
rents as a voltage across a sense resistor (see R
in Fig-
ure 1). A filter between the negative battery terminal
and the SR pin is required.
3
bq2013H
FG2013H1.eps
PROG6
HDQ
SEG5/PROG5
SEG4/PROG4
SEG3/PROG3
SEG2/PROG2
SEG1/PROG1
VSS
DISP
SB
VCC
REF
bq2013H
Gas Gauge IC
LCOM
RBI
DONE
100K
Q1
ZVNL110A
R1
C1
RS
H, Z, or L
To
μ
C
RB1
0.1
μ
F
RB2
Load
Charger
To
μ
C or
Fast Charger
2. The battery stack voltage can be directly connect to VCC across 4 nickel cells
(4.8V nominal and should not exceed 6.5V) with a resistor and a zener diode
to limit voltage during charge. Otherwise, R1and Q1 are needed for
regulation of > 4 nickel cells.
3. Programming resistors and ESD-protection diodes are not shown.
4. R-C on SR is required.
SR
1. Indicates optional.
Notes:
Figure 1. Application Diagram: LED Display
相關PDF資料 |
PDF描述 |
|---|---|
| bq2014H | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
| bq2014 | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2013HEVM-001 | 功能描述:電源管理IC開發工具 BQ2013H Eval Kit for NiCd 16.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2013HSN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for Power- Assist Applications |
| BQ2013HSN-A514 | 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2013HSN-A514 | 制造商:Texas Instruments 功能描述:SEMICONDUCTORS ((NS)) |
| BQ2013HSN-A514G4 | 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。