- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2013H (Benchmark Technology Group) Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) PDF資料下載
參數資料
| 型號： | bq2013H |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC for Power-Assist Applications(應用于電源援助的氣體Gauge芯片) |
| 中文描述： | 氣體計IC，電源輔助應用（應用于電源援助的氣體計芯片） |
| 文件頁數： | 4/24頁 |
| 文件大?。?/td> | 195K |
| 代理商： | BQ2013H |
Register Backup
The bq2013H RBI input pin is intended to be used with
a storage capacitor to provide backup potential to the in-
ternal bq2013H registers when V
momentarily drops be-
low 3.0V. V
CC
is output on RBI when V
CC
is above 3.0V.
After V
rises above 3.0V, the bq2013H checks the internal
registers for data loss or corruption. If data has changed,
then the NAC register is cleared, and the LMD register is
loadedwiththeinitialPFC.
Voltage Thresholds
In conjunction with monitoring V
for charge/discharge
currents, the bq2013H monitors the battery potential
through the SB pin for the end-of-discharge voltage (EDV)
thresholds.
The EDV threshold levels are used to determine when
the battery has reached an “empty”state.
The EDV thresholds for the bq2013H are set as follows:
EDV1 (first) = 1.00V
EDVF (final) = EDV1 - 100mV
The battery voltage divider (RB1 and RB2 in Figure 1) is
used to scale these values to the desired threshold.
If VSB is below either of the two EDV thresholds for the
specified delay times in Table 1, the associated flag is
latched and remains latched, independent of VSB, until
the next valid charge. EDV monitoring is disabled if the
OVLD bit in FLGS2 is set.
Table 1.Delay Time in Seconds
Capacity
Temperature
10
°
C to 30
°
C
6
3
2
< 10
°
C
7
4
2
> 30
°
C
5
2
2
> 40%
20% to 40%
< 20%
Reset
The bq2013H can be reset by removing V
and ground-
ing the RBI pin for 15 seconds or with a command over
the serial port. The serial port reset command sequence
requires writing 00h to register PPFC (address = leh)
and the writing 00h to register LMD (address = 05h.)
Temperature
The bq2013H internally determines the temperature in
10°C steps centered from -35°C to +85°C. The tempera-
ture steps are used to adapt charge rate compensations
and self-discharge counting. The temperature range is
available over the serial port in 10°C increments as
shown in the following table:
TMPGG (hex)
0x
1x
2x
3x
4x
5x
6x
7x
8x
9x
Ax
Bx
Cx
Temperature Range
< -30°C
-30°C to -20°C
-20°C to -10°C
-10°C to 0°C
0°C to 10°C
10°C to 20°C
20°C to 30°C
30°C to 40°C
40°C to 50°C
50°C to 60°C
60°C to 70°C
70°C to 80°C
> 80°C
Layout Considerations
The bq2013H measures the voltage differential between
the SR and V
pins. V
(the offset voltage at the SR
pin) is greatly affected by PC board layout. For optimal
results, the PC board layout should follow the strict rule of
a single-point ground return.
ground with small signal ground causes undesirable noise
on the small signal nodes. Additionally:
Sharing high-current
I
The capacitors should be placed as close as possible
to the SB and V
pins and their paths to V
should
be as short as possible. A high-quality ceramic
capacitor of 0.1
μ
f is recommended for V
CC
.
I
The sense resistor (R
S
) should be as close as possible
to the bq2013H.
I
The R-C on the SR pin should be located as close as
possible to the SR pin. The maximum R should not
exceed 100K.
Gas Gauge Operation
The operational overview diagram in Figure 2 illus-
trates the operation of the bq2013H. The bq2013H ac-
cumulates a measure of charge and discharge currents,
as well as an estimation of self-discharge. The bq2013H
compensates charge current for charge rate and tem-
4
bq2013H
相關PDF資料 |
PDF描述 |
|---|---|
| bq2014H | Low-Cost NiCd/NiMH Gas Gauge IC(低價格NiCd/NiMHGas Gauge芯片) |
| bq2014 | Gas Gauge IC with External Charge Control(氣體Gauge（帶外部電荷控制）) |
| bq2040 | Gas Gauge IC With SMBus Interface(氣體Gauge芯片（帶SMBus 接口）) |
| bq2050H | Low-Cost Lithium Ion Power Gauge IC(低價格鋰離子電源氣體Gauge芯片) |
| bq2050 | Lithium Ion Power Gauge IC(鋰離子電源Gause 芯片) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2013HEVM-001 | 功能描述:電源管理IC開發工具 BQ2013H Eval Kit for NiCd 16.8V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2013HSN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for Power- Assist Applications |
| BQ2013HSN-A514 | 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2013HSN-A514 | 制造商:Texas Instruments 功能描述:SEMICONDUCTORS ((NS)) |
| BQ2013HSN-A514G4 | 功能描述:電池管理 NiCd/NiMH/Lead-Acid Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。