XENPAK-DEFINED REGISTERS (1.8000’H TO 1.8106’H) Note (1): User writes to these bits are not valid unless the Command Status is Idle. The Comman" />
參數資料
型號: BBT3821LP-JH
廠商: Intersil
文件頁數: 17/75頁
文件大小: 0K
描述: IC RE-TIMER OCTAL 192-BGA
標準包裝: 90
類型: 時鐘和數據恢復(CDR),多路復用器
PLL:
輸入: CML
輸出: CML,CMOS
電路數: 1
比率 - 輸入:輸出: 8:8
差分 - 輸入:輸出: 是/是
頻率 - 最大: 1.59Gbps
電源電壓: 1.3 V ~ 2.5 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 192-EBGA
供應商設備封裝: 192-EBGA-B(17x17)
包裝: 托盤
24
XENPAK-DEFINED REGISTERS (1.8000’H TO 1.8106’H)
Note (1): User writes to these bits are not valid unless the Command Status is Idle. The Command Status will not return to Idle until read after command completion
(either Succeed or Failed).
Note (2): At the end of a hardware RESET via the RSTN pin, on powerup, or on a register [1,3,4].0.15 RESET operation, and if the XP_ENA pin is asserted, the
BBT3821 will automatically begin an ‘all NVR read’ operation.
Note (3): The single byte commands are controlled through the bits of the registers at 1.32769:32774 (1.8001:8006’h). The ‘block write/read’ commands are affected by
register 1.32773 (1.8005’h). Additional status is available in 1.327743 (1.8006’h)
Note (1): 8-bit-addressed I2C devices are addressed using bits 7:0. Never set bit 1.32773.8 (1.8005’h.8) for 16-bit address operation with an 8-bit address I2C device.
Table 14. IEEE PACKAGE IDENTIFIER REGISTERS
MDIO REGISTER ADDRESSES = 1.14:15 (1.000E:F’h)
BIT
NAME
SETTING
DEFAULT
R/W
DESCRIPTION
1.14.15:0
Package ID
Package OUI bits 3:24 &
etc.
00’h
R/W
If NVR is loaded, these are copies of
1.32818:32819 (1.8032:8033’h) & 1.32820:32821
(1.8034:8035’h)
1.15.15:0
Package ID
00’h
R/W
Table 15. XENPAK NVR CONTROL & STATUS REGISTER
MDIO (XENPAK) REGISTER ADDRESS = 1.32768 (1.8000’h)
BIT
NAME
SETTING
DEFAULT
R/W
DESCRIPTION
1.32768.15:6
Reserved
000’h
R/W
1.32768.5
NVR Command(1)
1 = Write NVR
0 = Read NVR
0’b(2)
R/W
Write/Read Control for I2C operation
1.32768.4
Reserved
0’b
RO
1.32768.3:2
NVR Command
Status(3)
Current Status of
NVR Command
00’b
RO
11 = Command failed
10 = Command in progress/Queued
01 = Command completed with success
00 = Idle
1.32768.1:0
Extended NVR
Command
NVR operation to be
performed
11’b(2)
R/W
10 = read/write one byte(3)
11 = read/write all NVR contents(3)
Other values = reserved
Table 16. I2C ONE-BYTE OPERATION DEVICE ADDRESS REGISTER
MDIO REGISTER ADDRESS = 1.32769 (1.8001’h)
BIT
NAME
SETTING
DEFAULT
R/W
DESCRIPTION
1.32769.15:8
Reserved
00’h
RO
1.32769.7:0
Device
Address
I2C Device address to
access
A2’h
R/W
All I2C Device addresses are even. Bit 0 cannot be set.
Table 17. I2C ONE-BYTE OPERATION MEMORY ADDRESS REGISTER
MDIO REGISTER, ADDRESS = 1.32770 (1.8002’h)
BIT
NAME
SETTING
DEFAULT
R/W
DESCRIPTION
1.32770.15:0
Memory
Address
I2C Memory address to
access
0000’h(2)
R/W
I2C Memory Address within Device address of 1.32769
(1.8001’h)
Table 18. I2C ONE-BYTE OPERATION READ DATA REGISTER
MDIO REGISTER ADDRESS = 1.32771 (1.8003’h)
BIT
NAME
SETTING
DEFAULT
R/W
DESCRIPTION
1.32771.15:8
Reserved
00’h
RO
1.32771.7:0
Read Data
I2C Read Data
00’h
RO
Result of I2C 1-byte Read operation
BBT3821
相關PDF資料
PDF描述
BH2219FVM-TR IC DAC 8BIT 2-CHAN MSOP8
BH2223FV-E2 IC CONV D/A 8BIT 10CH SSOP-B16
BH2226FV-FE2 IC DAC 8BIT 8-CHAN SSOP-B16
BH2228FV-E2 IC DAC 8BIT 6-CHAN SSOP-B14
BQ4285EP IC RTC W/114X8 NVSRAM 24-DIP
相關代理商/技術參數
參數描述
BBTEKIT 功能描述:剝線和切削工具 COMPR AND STRIP TOOL KIT FOR RG59 RG6 CBL RoHS:否 制造商:Molex 產品:Cable Strippers 類型: 描述/功能:Stripper
BB-TERM3 功能描述:固定接線端子 3-Position Terminal Block Breakout RoHS:否 制造商:Phoenix Contact 產品:Fixed Terminal Blocks 類型:Wire to Board 節距:5.08 mm 位置/觸點數量:2 線規量程:26-16 電流額定值:13.5 A 電壓額定值:250 V 安裝風格:Through Hole 安裝角:Straight 端接類型:Screw 觸點電鍍:
BB-TG.30.8113 功能描述:ANT LTE, TERMINAL 制造商:b&b smartworx, inc. 系列:- 零件狀態:在售 配件類型:天線 配套使用產品/相關產品:- 標準包裝:1
BBU-03 制造商:Highpoint Technology 功能描述:BATTERY BACK UP - Bulk
BBU-03F 制造商:Highpoint Technology 功能描述:UNIVERSAL BATTERY BACKUP - Bulk