參數資料
型號: ATTINY2313A-SUR
廠商: Atmel
文件頁數: 126/172頁
文件大?。?/td> 0K
描述: MCU AVR 2KB FLASH 20MHZ 20SOIC
產品培訓模塊: tinyAVR Introduction
標準包裝: 1,000
系列: AVR® ATtiny
核心處理器: AVR
芯體尺寸: 8-位
速度: 20MHz
連通性: I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 18
程序存儲器容量: 2KB(1K x 16)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 128 x 8
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 1.8 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 20-SOIC(0.295",7.50mm 寬)
包裝: 帶卷 (TR)
其它名稱: ATTINY2313A-SUR-ND
57
8246B–AVR–09/11
ATtiny2313A/4313
10.1.2
Toggling the Pin
Writing a logic one to PINxn toggles the value of PORTxn, independent on the value of DDRxn.
Note that the SBI instruction can be used to toggle one single bit in a port.
10.1.3
Switching Between Input and Output
When switching between tri-state ({DDxn, PORTxn} = 0b00) and output high ({DDxn, PORTxn}
= 0b11), an intermediate state with either pull-up enabled {DDxn, PORTxn} = 0b01) or output
low ({DDxn, PORTxn} = 0b10) must occur. Normally, the pull-up enabled state is fully accept-
able, as a high-impedant environment will not notice the difference between a strong high driver
and a pull-up. If this is not the case, the PUD bit in the MCUCR Register can be set to disable all
pull-ups in all ports.
Switching between input with pull-up and output low generates the same problem. The user
must use either the tri-state ({DDxn, PORTxn} = 0b00) or the output high state ({DDxn, PORTxn}
= 0b10) as an intermediate step.
Table 10-1 summarizes the control signals for the pin value.
10.1.4
Reading the Pin Value
Independent of the setting of Data Direction bit DDxn, the port pin can be read through the
PINxn Register bit. As shown in Figure 10-2 on page 56, the PINxn Register bit and the preced-
ing latch constitute a synchronizer. This is needed to avoid metastability if the physical pin
changes value near the edge of the internal clock, but it also introduces a delay. Figure 10-3
shows a timing diagram of the synchronization when reading an externally applied pin value.
The maximum and minimum propagation delays are denoted t
pd,max and tpd,min respectively.
Figure 10-3. Synchronization when Reading an Externally Applied Pin value
Table 10-1.
Port Pin Configurations
DDxn
PORTxn
PUD
(in MCUCR)
I/O
Pull-up
Comment
0
X
Input
No
Tri-state (Hi-Z)
0
1
0
Input
Yes
Pxn will source current if ext. pulled low
0
1
Input
No
Tri-state (Hi-Z)
1
0
X
Output
No
Output Low (Sink)
1
X
Output
No
Output High (Source)
XXX
in r17, PINx
0x00
0xFF
INSTRUCTIONS
SYNC LATCH
PINxn
r17
XXX
SYSTEM CLK
t
pd, max
t pd, min
相關PDF資料
PDF描述
ATTINY24A-MFR MCU AVR 2KB FLASH 20MHZ 20QFN
PCA9575PW2,118 IC I2C/SMBUS 16BIT GPIO 28TSSOP
ATTINY44A-SSUR MCU AVR 4KB FLASH 20MHZ 14SOIC
PCA8575D,112 IC I/O EXPANDER I2C 16B 24SOIC
PCA9535CPW,118 IC I/O EXPANDER I2C 16B 24TSSOP
相關代理商/技術參數
參數描述
ATTINY2313V 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATTINY2313V_06 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATtiny2313V-10MI 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM 1 UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATtiny2313V-10MU 功能描述:8位微控制器 -MCU 2kB Flash 0.128kB EEPROM 18 I/O Pins RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY2313V-10MUR 功能描述:8位微控制器 -MCU AVR 2KFL 128B EE1.8V 128B 1UART 20P-10MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT