參數資料
型號： ATTINY2313A-SUR
廠商： Atmel
文件頁數： 103/172頁
文件大?。?/td> 0K
描述： MCU AVR 2KB FLASH 20MHZ 20SOIC
產品培訓模塊： tinyAVR Introduction
標準包裝： 1,000
系列： AVR® ATtiny
核心處理器： AVR
芯體尺寸： 8-位
速度： 20MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 18
程序存儲器容量： 2KB（1K x 16）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 128 x 8
RAM 容量： 128 x 8
電壓 - 電源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
包裝： 帶卷 (TR)
其它名稱： ATTINY2313A-SUR-ND
36
8246B–AVR–09/11
ATtiny2313A/4313
Peripheral shutdown can be used in Idle mode and Active mode to significantly reduce the over-
all power consumption. See “Effect of Power Reduction” on page 206 for examples. In all other
sleep modes, the clock is already stopped.
7.4
Minimizing Power Consumption
There are several issues to consider when trying to minimize the power consumption in an AVR
controlled system. In general, sleep modes should be used as much as possible, and the sleep
mode should be selected so that as few as possible of the device’s functions are operating. All
functions not needed should be disabled. In particular, the following modules may need special
consideration when trying to achieve the lowest possible power consumption.
7.4.1
Analog Comparator
When entering Idle mode, the Analog Comparator should be disabled if not used. In the other
sleep modes, the Analog Comparator is automatically disabled. However, if the Analog Compar-
ator is set up to use the Internal Voltage Reference as input, the Analog Comparator should be
disabled in all sleep modes. Otherwise, the Internal Voltage Reference will be enabled, indepen-
dent of sleep mode. See “Analog Comparator” on page 168 for details on how to configure the
Analog Comparator.
7.4.2
Internal Voltage Reference
The Internal Voltage Reference will be enabled when needed by the Brown-out Detection or the
Analog Comparator. If these modules are disabled as described in the sections above, the inter-
nal voltage reference will be disabled and it will not be consuming power. When turned on again,
the user must allow the reference to start up before the output is used. If the reference is kept on
in sleep mode, the output can be used immediately. See “Internal Voltage Reference” on page
42 for details on the start-up time.
7.4.3
Brown-out Detector
If the Brown-out Detector is not needed in the application, this module should be turned off. If the
Brown-out Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep modes,
and hence, always consume power. In the deeper sleep modes, this will contribute significantly
to the total current consumption. See “Brown-out Detection” on page 41 and “Software BOD Dis-
able” on page 35 for details on how to configure the Brown-out Detector.
7.4.4
Watchdog Timer
If the Watchdog Timer is not needed in the application, this module should be turned off. If the
Watchdog Timer is enabled, it will be enabled in all sleep modes, and hence, always consume
power. In the deeper sleep modes, this will contribute significantly to the total current consump-
tion. See “Interrupts” on page 48 for details on how to configure the Watchdog Timer.
7.4.5
Port Pins
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important thing is then to ensure that no pins drive resistive loads. In sleep modes where
the I/O clock (clk
I/O) is stopped, the input buffers of the device will be disabled. This ensures that
no power is consumed by the input logic when not needed. In some cases, the input logic is
needed for detecting wake-up conditions, and it will then be enabled. See the section “Digital
Input Enable and Sleep Modes” on page 58 for details on which pins are enabled. If the input
buffer is enabled and the input signal is left floating or has an analog signal level close to V
CC/2,
the input buffer will use excessive power.
相關PDF資料
PDF描述
ATTINY24A-MFR MCU AVR 2KB FLASH 20MHZ 20QFN
PCA9575PW2,118 IC I2C/SMBUS 16BIT GPIO 28TSSOP
ATTINY44A-SSUR MCU AVR 4KB FLASH 20MHZ 14SOIC
PCA8575D,112 IC I/O EXPANDER I2C 16B 24SOIC
PCA9535CPW,118 IC I/O EXPANDER I2C 16B 24TSSOP
相關代理商/技術參數
參數描述
ATTINY2313V 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATTINY2313V_06 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2K Bytes In-System Programmable Flash
ATtiny2313V-10MI 功能描述:8位微控制器 -MCU AVR 2K FLSH 128B EE 128B SRAM 1 UART RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATtiny2313V-10MU 功能描述:8位微控制器 -MCU 2kB Flash 0.128kB EEPROM 18 I/O Pins RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY2313V-10MUR 功能描述:8位微控制器 -MCU AVR 2KFL 128B EE1.8V 128B 1UART 20P-10MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*