參數資料
型號: AM79C961AKIW
廠商: ADVANCED MICRO DEVICES INC
元件分類: 微控制器/微處理器
英文描述: PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
中文描述: 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP132
封裝: PLASTIC, QFP-132
文件頁數: 70/206頁
文件大小: 1507K
代理商: AM79C961AKIW
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁當前第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁
70
Am79C961A
the above paragraph) of the current RDTE shows valid
ownership, then it proceeds to a poll of the next RDTE.
Following this poll, and regardless of the outcome of
this poll, transfers of receive data from the FIFO may
begin.
Regardless of ownership of the second receive
descriptor, the PCnet-ISA II controller will continue to
perform receive data DMA transfers to the first buffer,
using burst-cycle DMA transfers. If the packet length
exceeds the length of the first buffer, and the PC-
net-ISA II
controller does not own the second buffer,
ownership of the current descriptor will be passed back
to the system by writing a zero to the OWN bit of RMD1
and status will be written indicating buffer (BUFF = 1)
and possibly overflow (OFLO = 1) errors.
If the packet length exceeds the length of the first (cur-
rent) buffer, and the PCnet-ISA II controller does own
the second (next) buffer, ownership will be passed
back to the system by writing a zero to the OWN bit of
RMD1 when the first buffer is full. Receive data trans-
fers to the second buffer may occur before the PC-
net-ISA II controller proceeds to look ahead to the
ownership of the third buffer. Such action will depend
upon the state of the FIFO when the status has been
updated on the first descriptor. In any case, lookahead
will be performed to the third buffer and the information
gathered will be stored in the chip, regardless of the
state of the ownership bit. As in the transmit flow, loo-
kahead operations are performed only once.
This activity continues until the PCnet-ISA II controller
recognizes the completion of the packet (the last byte of
this receive message has been removed from the
FIFO). The PCnet-ISA II controller will subsequently up-
date the current RDTE status with the end of packet
(ENP) indication set, write the message byte count
(MCNT) of the complete packet into RMD2 and over-
write the
current
entries in the CSRs with the
next
en-
tries.
Media Access Control
The Media Access Control engine incorporates the
essential protocol requirements for operation of a com-
pliant Ethernet/802.3 node, and provides the interface
between the FIFO sub-system and the Manchester
Encoder/Decoder (MENDEC).
This section describes operation of the MAC engine
when operating in Half Duplex mode. When in Half
Duplex mode, the MAC engine is fully compliant to Sec-
tion 4 of ISO/IEC 8802-3 (ANSI/IEEE Standard 1990
Second Edition) and ANSI/IEEE 802.3 (1985). When
operating in Full Duplex mode, the MAC engine behavior
changes as described in the Full Duplex Operation sec-
tion.
The MAC engine provides programmable enhanced
features designed to minimize host supervision and pre
or post-message processing. These features include
the ability to disable retries after a collision, dynamic
FCS generation on a packet-by-packet basis, and au-
tomatic pad field insertion and deletion to enforce
minimum frame size attributes.
The two primary attributes of the MAC engine are:
I
Transmit and receive message data encapsulation
Framing (frame boundary delimitation, frame
synchronization)
Addressing (source and destination address
handling)
Error detection (physical medium transmission
errors)
I
Media access management
Medium allocation (collision avoidance)
Contention resolution (collision handling)
Transmit and Receive Message Data
Encapsulation
The MAC engine provides minimum frame size
enforcement for transmit and receive packets. When
APAD_XMT = 1 (bit 11 in CSR4), transmit messages
will be padded with sufficient bytes (containing 00h) to
ensure that the receiving station will observe an infor-
mation field (destination address, source address,
length/type, data and FCS) of 64-bytes. When
ASTRP_RCV = 1 (bit 10 in CSR4), the receiver will
automatically strip pad bytes from the received mes-
sage by observing the value in the length field, and
stripping excess bytes if this value is below the mini-
mum data size (46 bytes). Both features can be inde-
pendently over-ridden to allow illegally short (less than
64 bytes of packet data) messages to be transmitted
and/or received. The use of these features reduce bus
bandwidth usage because the pad bytes are not trans-
ferred to or from host memory.
Framing (frame boundary delimitation, frame
synchronization)
The MAC engine will autonomously handle the con-
struction of the transmit frame. Once the Transmit FIFO
has been filled to the predetermined threshold (set by
XMTSP in CSR80), and providing access to the chan-
nel is currently permitted, the MAC engine will com-
mence the 7-byte preamble sequence (10101010b,
where first bit transmitted is a 1). The MAC engine will
subsequently append the Start Frame Delimiter (SFD)
byte (10101011b) followed by the serialized data from
the Transmit FIFO. Once the data has been completed,
the MAC engine will append the FCS (most significant
bit first) which was computed on the entire data portion
of the message.
Note that the user is responsible for the correct order-
ing and content in each of the fields in the frame,
相關PDF資料
PDF描述
AM79C961AVCW PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
AM79C961AVIW PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA
Am79C965A PCnet?-32 Single-Chip 32-Bit Ethernet Controller
AM79C970AKCW PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
AM79C970AKC PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product
相關代理商/技術參數
參數描述
AM79C961APDLUTS 制造商:Advanced Micro Devices 功能描述:
AM79C961AVC 制造商:Rochester Electronics LLC 功能描述: 制造商:Advanced Micro Devices 功能描述:LAN Node Controller, 144 Pin, TQFP
AM79C961AVC/W 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
AM79C961AVC\\W 制造商:Rochester Electronics LLC 功能描述:
AM79C961AVC\W 制造商:Rochester Electronics LLC 功能描述: