- 您現在的位置：買賣IC網 > PDF目錄375289 > AM29BDS640GTC9WSI (SPANSION LLC) 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory PDF資料下載
參數資料
| 型號： | AM29BDS640GTC9WSI |
| 廠商： | SPANSION LLC |
| 元件分類： | DRAM |
| 英文描述： | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| 中文描述： | 4M X 16 FLASH 1.8V PROM, 20 ns, PBGA80 |
| 封裝： | 11 X 12 MM, 0.80 MM PITCH, FBGA-80 |
| 文件頁數： | 15/65頁 |
| 文件大小： | 899K |
| 代理商： | AM29BDS640GTC9WSI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
14
Am29BDS640G
October 31, 2002
A D V A N C E I N F O R M A T I O N
Standby Mode
When the system is not reading or writing to the device,
it can place the device in the standby mode. In this
mode, current consumption is greatly reduced, and the
outputs are placed in the high impedance state, inde-
pendent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# inputs are both held at V
CC
± 0.2 V.
The device requires standard access time (t
CE
) for
read access, before it is ready to read data.
If the device is deselected during erasure or program-
ming, the device draws active current until the opera-
tion is completed.
I
CC3
in the DC Characteristics table represents the
standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device
energy consumption. While in asynchronous mode, the
device automatically enables this mode when
addresses remain stable for t
ACC
+ 60 ns. The auto-
matic sleep mode is independent of the CE#, WE#, and
OE# control signals. Standard address access timings
provide new data when addresses are changed. While
in sleep mode, output data is latched and always avail-
able to the system. While in synchronous mode, the
device automatically enables this mode when either
the first active CLK edge occurs after t
ACC
or the CLK
runs slower than 5MHz. Note that a new burst opera-
tion is required to provide new data.
I
CC4
in the
“DC Characteristics” section on page 35
represents the automatic sleep mode current specifica-
tion.
RESET#: Hardware Reset Input
The RESET# input provides a hardware method of
resetting the device to reading array data. When
RESET# is driven low for at least a period of t
RP
, the
device immediately terminates any operation in
progress, tristates all outputs, resets the configuration
register, and ignores all read/write commands for the
duration of the RESET# pulse. The device also resets
the internal state machine to reading array data. The
operation that was interrupted should be reinitiated
once the device is ready to accept another command
sequence, to ensure data integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at V
SS
± 0.2 V, the device
draws CMOS standby current (I
CC4
). If RESET# is held
at V
IL
but not within V
SS
± 0.2 V, the standby current will
be greater.
RESET# may be tied to the system reset circuitry. A
system reset would thus also reset the Flash memory,
enabling the system to read the boot-up firmware from
the Flash memory.
If RESET# is asserted during a program or erase oper-
ation, the device requires a time of t
READY
(during
Embedded Algorithms) before the device is ready to
read data again. If RESET# is asserted when a
program or erase operation is not executing, the reset
operation is completed within a time of t
READY
(not
during Embedded Algorithms). The system can read
data t
RH
after RESET# returns to V
IH
.
Refer to the AC Characteristics tables for RESET#
parameters and to
Figure 20, “Reset Timings,” on
page 47
for the timing diagram.
Output Disable Mode
When the OE# input is at V
IH
, output from the device is
disabled. The outputs are placed in the high imped-
ance state.
Hardware Data Protection
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to
Table 14, “Com-
mand Definitions,” on page 29
for command defini-
tions).
The device offers two types of data protection at the
sector level:
■
The sector lock/unlock command sequence dis-
ables or re-enables both program and erase opera-
tions in any sector.
■
When WP# is at V
IL
, sectors 0 and 1 (bottom boot)
or sectors 132 and 133 (top boot) are locked.
■
When ACC is at V
IL
, all sectors are locked.
The following hardware data protection measures
prevent accidental erasure or programming, which
might otherwise be caused by spurious system level
signals during V
CC
power-up and power-down transi-
tions, or from system noise.
Write Protect (WP#)
The Write Protect (WP#) input provides a hardware
method of protecting data without using V
ID
.
If the system asserts V
IL
on the WP# pin, the device
disables program and erase functions in sectors 0 and
1 (bottom boot) or sectors 132 and 133 (top boot).
If the system asserts V
IH
on the WP# pin, the device
reverts to whether the two outermost 8K Byte boot
sectors were last set to be protected or unprotected.
Note that the WP# pin must not be left floating or
unconnected; inconsistent behavior of the device may
result.
相關PDF資料 |
PDF描述 |
|---|---|
| AM29BDS640GTD3WSI | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| AM29BDS640GTD9WSI | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| AM29BDS640GTD8WSI | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| AM29BDS643GT7MVAI | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
| AM29BDS643GT5GVAI | 64 Megabit (4 M x 16-Bit) CMOS 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29BDS643GT5KVAI | 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays |
| AM29BL802CB-65RZET | 制造商:Spansion 功能描述: |
| AM29C01WW WAF | 制造商:Advanced Micro Devices 功能描述: |
| AM29C10API | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM29C10AWW DIE | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。