- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC836BCPZ (Analog Devices Inc)IC MCU 62K FLASH ADC/DAC 56LFCSP PDF資料下載
參數資料
| 型號： | ADUC836BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 39/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心處理器： | 8052 |
| 芯體尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 連通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外圍設備： | POR，PSM，PWM，溫度傳感器，WDT |
| 輸入/輸出數： | 34 |
| 程序存儲器容量： | 62KB（62K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 數據轉換器： | A/D 7x16b; D/A 1x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
ADuC836
–44–
ADuC836
–45–
SERIAL PERIPHERAL INTERFACE
The ADuC836 integrates a complete hardware Serial Peripheral
Interface (SPI) interface on-chip. SPI is an industry-standard
synchronous serial interface that allows eight bits of data to be
synchronously transmitted and received simultaneously, i.e., full-
duplex. It should be noted that the SPI pins SCLOCK and MOSI
are multiplexed with the I2C pins SCLOCK and SDATA.The pins
are controlled via the I2CCON SFR only if SPE is clear. SPI can
be configured for master or slave operation and typically consists of
four pins:
SCLOCK (Serial Clock I/O Pin), Pin 26
The master clock (SCLOCK) is used to synchronize the data
being transmitted and received through the MOSI and MISO
data lines. A single data bit is transmitted and received in each
SCLOCK period.Therefore, a byte is transmitted/received after
eight SCLOCK periods.The SCLOCK pin is configured as an
output in master mode and as an input in Slave mode. In Master
mode, the bit rate, polarity, and phase of the clock are controlled
by the CPOL, CPHA, SPR0, and SPR1 bits in the SPICON SFR
(see Table XXI). In Slave mode, the SPICON register will have
to be configured with the phase and polarity (CPHA and CPOL)
as the master, as for both Master and Slave modes the data is
transmitted on one edge of the SCLOCK signal and sampled on
the other.
MISO (Master In, Slave Out Data I/O Pin), Pin 14
The MISO (master in slave out) pin is configured as an input line
in Master mode and an output line in Slave mode.The MISO
line on the master (data in) should be connected to the MISO
line in the slave device (data out).The data is transferred as byte-
wide (8-bit) serial data, MSB first.
MOSI (Master Out, Slave In Pin), Pin 27
The MOSI (master out slave in) pin is configured as an output
line in Master mode and an input line in Slave mode.The MOSI
line on the master (data out) should be connected to the MOSI
line in the slave device (data in).The data is transferred as byte-
wide (8-bit) serial data, MSB first.
SS (Slave Select Input Pin), Pin 13
The Slave Select (SS) input pin is only used when the ADuC836
is configured in SPI Slave mode.This line is active low. Data is
only received or transmitted in Slave mode when the SS pin is low,
allowing the ADuC836 to be used in single master, multislave SPI
configurations. If CPHA = 1, the SS input may be permanently
pulled low.With CPHA = 0, the SS input must be driven low
before the first bit in a byte wide transmission or reception and
return high again after the last bit in that byte-wide transmission or
reception. In SPI Slave mode, the logic level on the external SS pin
(Pin 13) can be read via the SPR0 bit in the SPICON SFR.
The following SFR registers are used to control the SPI interface.
Table XXI. SPICON SFR Bit Designations
Bit
Name
Description
7
ISPI
SPI Interrupt Bit.
Set by MicroConverter at the end of each SPI transfer.
Cleared directly by user code or indirectly by reading the SPIDAT SFR.
6
WCOL
Write Collision Error Bit.
Set by MicroConverter if SPIDAT is written to while an SPI transfer is in progress.
Cleared by user code.
5
SPE
SPI Interface Enable Bit.
Set by user to enable the SPI interface.
Cleared by user to enable the I2C interface.
4
SPIM
SPI Master/Slave Mode Select Bit.
Set by user to enable Master mode operation (SCLOCK is an output).
Cleared by user to enable Slave mode operation (SCLOCK is an input).
3
CPOL*
Clock Polarity Select Bit.
Set by user if SCLOCK idles high.
Cleared by user if SCLOCK idles low.
2
CPHA*
Clock Phase Select Bit.
Set by user if leading SCLOCK edge is to transmit data.
Cleared by user if trailing SCLOCK edge is to transmit data.
1
SPR1
SPI Bit Rate Select Bits.
0
SPR0
These bits select the SCLOCK rate (bitrate) in Master mode as follows:
SPR1
SPR0
Selected Bit Rate
0
fCORE/2
0
1
fCORE/4
1
0
fCORE/8
1
fCORE/16
In SPI Slave mode, i.e., SPIM = 0, the logic level on the external SS pin (Pin 13), can be read via the SPR0 bit.
*The CPOL and CPHA bits should both contain the same values for master and slave devices.
REV. A
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC843BSZ62-5 | IC ADC 12BIT W/FLASH MCU 52-MQFP |
| ADUC845BCPZ62-5 | IC FLASH MCU W/24BIT ADC 56-CSP |
| ADUC847BCPZ62-5 | IC MCU FLASH W/24BIT ADC 56-CSP |
| ADV202BBCZ-135 | IC CODEC VIDEO 135MHZ 144CSPBGA |
| ADV212BBCZ-115 | IC CODEC VID JPEG 2000 121CSPBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC836BCPZ-REEL | 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC836BS | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52 |
| ADUC836BS | 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS)) |
| ADUC836BSZ | 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC841 | 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
發布緊急采購，3分鐘左右您將得到回復。