參數資料
型號： ADUC836BCPZ
廠商： Analog Devices Inc
文件頁數： 26/80頁
文件大小： 0K
描述： IC MCU 62K FLASH ADC/DAC 56LFCSP
標準包裝： 1
系列： MicroConverter® ADuC8xx
核心處理器： 8052
芯體尺寸： 8-位
速度： 12.58MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： POR，PSM，PWM，溫度傳感器，WDT
輸入/輸出數： 34
程序存儲器容量： 62KB（62K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 4K x 8
RAM 容量： 2.25K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.25 V
數據轉換器： A/D 7x16b; D/A 1x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 56-VFQFN 裸露焊盤，CSP
包裝： 托盤
ADuC836
–32–
ADuC836
–33–
Using the Flash/EE Data Memory
The 4 Kbytes of Flash/EE data memory are configured as
1024 pages, each of four bytes. As with the other ADuC836
peripherals, the interface to this memory space is via a group of
registers mapped in the SFR space. A group of four data regis-
ters (EDATA1–A4) is used to hold the four bytes of data at each
page.The page is addressed via the two registers EADRH and
EADRL. Finally, ECON is an 8-bit control register that may be
written with one of nine Flash/EE memory access commands to
trigger various read, write, erase, and verify functions.
A block diagram of the SFR interface to the Flash/EE data
memory array is shown in Figure 20.
ECON—Flash/EE Memory Control SFR
Programming of either the Flash/EE data memory or the Flash/EE
program memory is done through the Flash/EE Memory Control
SFR (ECON).This SFR allows the user to read, write, erase, or
verify the 4 Kbytes of Flash/EE data memory or the 56 Kbytes of
Flash/EE program memory.
BYTE 1
(0000H)
EDATA1
SF
R
BYTE 1
(0004H)
BYTE 1
(0008H)
BYTE 1
(000CH)
BYTE 1
(0FF8H)
BYTE 1
(0FFCH)
BYTE 2
(0001H)
EDATA2
SF
R
BYTE 2
(0005H)
BYTE 2
(0009H)
BYTE 2
(000DH)
BYTE 2
(0FF9H)
BYTE 2
(0FFDH)
BYTE 3
(0002H)
EDATA3
SF
R
BYTE 3
(0006H)
BYTE 3
(000AH)
BYTE 3
(000EH)
BYTE 3
(0FFAH)
BYTE 3
(0FFEH)
BYTE 4
(0003H)
EDATA4
SF
R
BYTE 4
(0007H)
BYTE 4
(000BH)
BYTE 4
(000FH)
BYTE 4
(0FFBH)
BYTE 4
(0FFFH)
01H
00H
02H
03H
3FEH
3FFH
PAGE
ADDRESS
(E
ADRH/L
)
BYTE
ADDRESSES
ARE GIVEN IN
BRACKETS
Figure 20. Flash/EE Data Memory Control and Configuration
Table XIV. ECON—Flash/EE Memory Commands
Command Description
ECON Value
(Normal Mode) (Power-On Default)
(ULOAD Mode)
01H
Results in four bytes in the Flash/EE data memory,
Not Implemented. Use the MOVC instruction.
READ
addressed by the page address EADRH/L, being read
into EDATA 1 to 4.
02H
Results in four bytes in EDATA1–A4 being written to the Results in bytes 0–255 of internal XRAM being written
WRITE
Flash/EE data memory, at the page address given by
to the 256 bytes of Flash/EE program memory at the
EADRH/L (0 EADRH/L < 0400H)
page address given by EADRH. (0 EADRH < E0H)
Note:The four bytes in the page being addressed must
Note:The 256 bytes in the page being addressed must
be pre-erased.
03H
Reserved Command
04H
Verifies if the data in EDATA1–4 is contained in the
Not Implemented. Use the MOVC and MOVX
VERIFY
page address given by EADRH/L. A subsequent read
instructions to verify the WRITE in software.
of the ECON SFR will result in a 0 being read if the
verification is valid, or a nonzero value being read
to indicate an invalid verification.
05H
Results in the erase of the 4-bytes page of Flash/EE
Results in the 64-byte page of Flash/EE program
ERASE PAGE
data memory addressed by the page address EADRH/L
memory, addressed by the byte address EADRH/L
being erased. EADRL can equal any of 64 locations
within the page. A new page starts whenever EADRL
is equal to 00H, 40H, 80H, or C0H.
06H
Results in the erase of entire four Kbytes of Flash/EE
Results in the erase of the entire 56 Kbytes of ULOAD
ERASE ALL
data memory.
Flash/EE program memory.
81H
Results in the byte in the Flash/EE data memory,
Not Implemented. Use the MOVC command.
READBYTE
addressed by the byte address EADRH/L, being read
into EDATA1. (0 EADRH/L 0FFFH).
82H
Results in the byte in EDATA1 being written into
WRITEBYTE
Flash/EE data memory, at the byte address EADRH/L.
Flash/EE program memory at the byte address
EADRH/L (0 EADRH/L DFFFH).
0FH
Leaves the ECON instructions to operate on the
Enters Normal mode, directing subsequent ECON
EXULOAD
Flash/EE data memory.
instructions to operate on the Flash/EE data memory.
F0H
Enters ULOAD mode, directing subsequent ECON
Leaves the ECON instructions to operate on the Flash/EE
ULOAD
instructions to operate on the Flash/EE program memory.
program memory.
REV. A
相關PDF資料
PDF描述
ADUC843BSZ62-5 IC ADC 12BIT W/FLASH MCU 52-MQFP
ADUC845BCPZ62-5 IC FLASH MCU W/24BIT ADC 56-CSP
ADUC847BCPZ62-5 IC MCU FLASH W/24BIT ADC 56-CSP
ADV202BBCZ-135 IC CODEC VIDEO 135MHZ 144CSPBGA
ADV212BBCZ-115 IC CODEC VID JPEG 2000 121CSPBGA
相關代理商/技術參數
參數描述
ADUC836BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC836BS 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:8BIT MCU +16BIT DUAL ADC MQFP52
ADUC836BS 制造商:Analog Devices 功能描述:IC SEMICONDUCTOR ((NS))
ADUC836BSZ 功能描述:IC ADC DUAL 16BIT W/MCU 52-MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
ADUC841 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*