參數資料
型號： ADUC702
廠商： Analog Devices, Inc.
英文描述： 5 AMP MINIATURE POWER RELAY
中文描述： 精密模擬微控制器的12位模擬I / O，ARM7TDMI的微控制器
文件頁數： 42/80頁
文件大?。?/td> 840K
代理商： ADUC702
ADuC702x Series
Preliminary Technical Data
DIGITAL PERIPHERALS
THREE-PHASE PWM
Rev. PrB | Page 42 of 80
General overview
The ADuC702x provides a flexible, programmable, three-phase
PWM waveform generator that can be programmed to generate
the required switching patterns to drive a three-phase voltage
source inverter for ac induction (ACIM) motor control.
The PWM generator produces three pairs of PWM signal on
the six PWM output pins (PWM0H, PWM0L, PWM1H,
PWM1L, PWM2H, and PWM2L). The six PWM output signals
consist of three high-side drive signals and three low-side drive
signals.
The switching frequency and dead time of the generated PWM
patterns are programmable using the PWMDAT0 and
PWMDAT1 MMRs. In addition, three duty-cycle control
registers (PWMCH0, PWMCH1 and PWMCH2) directly
control the duty cycles of the three-pairs of PWM signals.
Each of the six PWM output signals can be enabled or disabled
by separate output enable bits of the PWMEN register. In
addition, three control bits of the PWMEN register permit
crossover of the two signals of a PWM pair. In crossover mode,
the PWM signal destined for the high side switch is diverted to
the complementary low side output and the signal destined for
the low side switch is diverted to the corresponding high side
output signal.
In many applications, there is a need to provide an isolation
barrier in the gate-drive circuits that turns on the power devices
of the inverter. In general, there are two common isolation
techniques,
optical
isolation
transformer isolation using pulse transformers. The PWM
controller permits mixing of the output PWM signals with a
high frequency chopping signal to permit easy interface to such
pulse transformers. The features of this gate-drive chopping
mode can be controlled by the PWMCFG register. An 8-bit
value within the PWMCFG register directly controls the
chopping frequency. High frequency chopping can be
independently enabled for the high-side and the low-side
outputs using separate control bits in the PWMCFG register.
using
opto-couplers
and
The PWM generator is capable of operating in two distinct
modes, single update mode or double update mode. In single
update mode the duty cycle values are programmable only once
per PWM period, so that the resultant PWM patterns are
symmetrical about the midpoint of the PWM period. In the
double update mode, a second updating of the PWM duty cycle
values is implemented at the midpoint of the PWM period. In
this mode, it is possible to produce asymmetrical PWM
patterns, that produce lower harmonic distortion in three-phase
PWM inverters. This technique also permits closed loop
controllers to change the average voltage applied to the machine
windings at a faster rate and so permits faster closed loop
bandwidths to be achieved. The operating mode of the PWM
block is selected by a control bit in the PWMCON register. In
single update mode a PWMSYNC pulse is produced at the start
of each PWM period. In double update mode, an additional
PWMSYNC pulse is produced at the midpoint of each PWM
period.
The PWM block can also provide an internal synchronisation
pulse on the SYNC pin that is synchronise to the PWM
switching frequency. In single update mode a pulse is produce
at the start of each PWM period. In double update mode, an
additional pulse is also produced at the mid-point of each
PWM period. The width of the pulse is programmable through
the PWMDAT2 register. The PWM block can also accept an
external synchronisation pulse on the SYNC pin. The selection
of external synchronisation or internal synchronisation is in the
PWMCON register. The SYNC input timing can be
synchronised to the internal peripheral clock, which is selected
in the PWMCON register. If the external synchronisation pulse
from the chip pin is asynchronous to the internal peripheral
clock (typical case), the external SYNC is considered
asynchronous and should be synchronised. The synchronisation
logic will add latency add jitter from the external pulse to the
actual PWM outputs. The size of the pulse on the SYNC pin
must be greater than two core clock periods.
The PWM signals produced by the ADuC702x can be shut off
via a dedicated asynchronous PWM shutdown pin,
PWMTRIP
,
that, when brought low, instantaneously places all six PWM
outputs in the OFF state (high). This hardware shutdown
mechanism is asynchronous so that the associated PWM
disable circuitry does not go through any clocked logic, thereby
ensuring correct PWM shutdown even in the event of a loss of
the core clock.
Status information about the PWM system is available to the
user in the PWMSTA register. In particular, the state of the
PWMTRIP
pin is available, as well as a status bit that indicates
whether operation is in the first half or the second half of the
PWM period.
Description of the PWM block
A functional block diagram of the PWM controller is shown in
Figure 21. The generation of the six output PWM signals on
pins PWM0H to PWM2L is controlled by four important
blocks:
The Three-Phase PWM Timing Unit, which is the core of the
PWM controller. It generates three pairs of complemented and
dead-time-adjusted centre-based PWM signals.
The Output Control Unit allows the redirection of the outputs
of the Three-Phase Timing Unit for each channel to either the
相關PDF資料
PDF描述
ADUC814ARU-REEL7 Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No
ADUC814BRU Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:37; Connector Shell Size:25; Connecting Termination:Crimp; Circular Shell Style:Jam Nut Receptacle; Body Style:Straight RoHS Compliant: No
ADUC814BRU-REEL Circular Connector; No. of Contacts:56; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-4
ADUC814BRU-REEL7 Circular Connector; No. of Contacts:61; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Pin; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-61
ADUC814 MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU
相關代理商/技術參數
參數描述
ADUC7020 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7020BCP62 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays
ADUC7020BCP62-U1 制造商:Analog Devices 功能描述:FLASH ARM7+5-CH,12-B ADC & 4X12-B DAC IC - Trays
ADUC7020BCPZ62 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
ADUC7020BCPZ62I 功能描述:IC MCU FLSH 62K ANLG I/O 40LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*