參數資料
型號： ADMCF341BR
廠商： ANALOG DEVICES INC
元件分類： 數字信號處理
英文描述： DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End
中文描述： 0-BIT, 10 MHz, OTHER DSP, PDSO28
封裝： SOIC-28
文件頁數： 11/36頁
文件大?。?/td> 1106K
代理商： ADMCF341BR
REV. 0
ADMCF341
–11–
PWMTRIP
OR
PWMSWT (0)
OVER-
CURRENT
TRIP
PWM SHUTDOWN CONTROLLER
ANALOG BLOCK
PWMTRIP
I
SENSE
2
I
SENSE
3
I
SENSE
1
PWMSEG (8...0)
OUTPUT
CONTROL
UNIT
GATE
DRIVE
UNIT
CLK
PWM DUTY CYCLE
REGISTERS
PWM CONFIGURATION
REGISTERS
TO INTERRUPT
CONTROLLER
THREE-PHASE
PWM TIMING
UNIT
CLK
RESET
SYNC
SYNC
PWMSYNC
CLKOUT
AH
AL
BH
BL
CH
CL
PWMGATE (9...0)
PWMTM (15...0)
PWMDT (9...0)
PWMPD (9...0)
PWMSYNCWT (7...0)
MODECTRL (6)
PWMCHA (15...0)
PWMCHB (15...0)
PWMCHC (15...0)
Figure 6. Overview of the PWM Controller of the ADMCF341
The ADMCF341 sets all internal stack pointers to the empty
stack condition, masks all interrupts, clears the MSTAT register,
and performs a full reset of all of the motor control peripherals.
Following a power-up, it is possible to initiate a DSP core and
motor control peripheral reset by pulling the RESET pin low.
The RESET signal must be the minimum pulsewidth specifica-
tion, t
RSP
. Following the reset sequence, the DSP core starts
executing code from the internal PM ROM located at 0x0800.
DSP Control Registers
The DSP core has a system control register, SYSCNTL,
memory-mapped at DM (0x3FFF). SPORT1 must be configured
as a serial port by setting Bit 10. SPORT0 and SPORT1 are
enabled by setting Bit 11 and Bit 12.
The DSP core has a wait state control register, MEMWAIT,
memory-mapped at DM (0x3FFE). The default value of this
register is 0xFFFF. For proper operation of the ADMCF341,
this register must always contain the value 0x8000. This value
sets the minimum access time to the program memory.
The configurations of both the SYSCNTL and MEMWAIT regis-
ters of the ADMCF341 are shown at the end of the data sheet.
THREE-PHASE PWM CONTROLLER
Overview
The PWM generator block of the ADMCF341 is a flexible,
programmable three-phase PWM waveform generator that can
be programmed to generate the required switching patterns to
drive a three-phase voltage source inverter for ac induction
motors (ACIM) or permanent magnet synchronous motors
(PMSM). In addition, the PWM block contains special func-
tions that considerably simplify the generation of the required
PWM switching patterns for control of brushless dc motors
(BDCM), including electronically commutated motors (ECM).
The six PWM output signals consist of three high side drive
signals (AH, BH, and CH) and three low side drive signals
(AL, BL, and CL). The switching frequency, dead time, and
minimum pulsewidths of the generated PWM patterns are pro-
grammable using, respectively, the PWMTM, PWMDT, and
PWMPD registers. In addition, three registers (PWMCHA,
PWMCHB, and PWMCHC) control the duty cycles of the
three pairs of PWM signals.
Each of the six PWM output signals can be enabled or disabled
by separate output enable bits of the PWMSEG register. In
addition, three control bits of the PWMSEG register permit
crossover of the two signals of a PWM pair for easy control of
ECM or BDCM. In crossover mode, the high side PWM signals
are diverted to the complementary low side output and the low
side signals are diverted to the corresponding high side outputs.
In many applications, there is a need to provide an isolation
barrier in the gate-drive circuits that turn on the power devices
of the inverter. In general, there are two common isolation
techniques: optical isolation using optocouplers, and trans-
former isolation using pulse transformers. The PWM controller
of the ADMCF341 permits mixing of the output PWM signals
with a high-frequency chopping signal to permit an easy inter-
face to such pulse transformers. The features of this gate-drive
chopping mode can be controlled by the PWMGATE register.
There is an 8-bit value within the PWMGATE register that
directly controls the chopping frequency. In addition, high-
frequency chopping can be independently enabled for the high
side and the low side outputs using separate control bits in the
PWMGATE register.
相關PDF資料
PDF描述
ADMCF341-EVALKIT DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End
ADN2811 OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp
ADN2811ACP-CML OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp
ADN2811ACP-CML-RL OC-48/OC-48 FEC Clock and Data Recovery IC with Integrated Limiting Amp
ADN2812 Continuous Rate 12.3 Mb/s to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp
相關代理商/技術參數
參數描述
ADMCF341BRZ-REEL 制造商:Analog Devices 功能描述:
ADMCF341-EVALKIT 制造商:AD 制造商全稱:Analog Devices 功能描述:DashDSP⑩ 28-Lead Flash Mixed-Signal DSP with Enhanced Analog Front End
AD-MCX-RPSMAF 功能描述:ADAPTER AU RPSMA FEM-MCX APPLE RoHS:是 類別:RF/IF 和 RFID >> RF配件 系列:* 標準包裝:1 系列:*
AD-MD3FF 制造商:Pan Pacific 功能描述:
AD-MD4FF 制造商:Pan Pacific 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*