- 您現在的位置：買賣IC網 > PDF目錄374016 > ADM9240 (Analog Devices, Inc.) Low Cost Microprocessor System Hardware Monitor PDF資料下載
參數資料
| 型號： | ADM9240 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low Cost Microprocessor System Hardware Monitor |
| 中文描述： | 低成本的微處理器系統硬件監視器 |
| 文件頁數： | 13/22頁 |
| 文件大?。?/td> | 280K |
| 代理商： | ADM9240 |
ADM9240
–13–
REV. 0
T o accommodate fans of different speed and/or different num-
bers of output pulses per revolution, a prescaler (divisor) of 1, 2,
4 or 8 may be added before the counter. T he default value is 2,
which gives a count of 153 for a fan running at 4400 rpm pro-
ducing two output pulses per revolution.
T he count is calculated by the equation:
Count
= (22.5
×
10
3
×
60) /(
rpm
×
Divisor
)
For constant speed fans, fan failure is normally considered to
have occurred when the speed drops below 70% of nominal,
which would correspond to a count of 219. Full scale (255)
would be reached if the fan speed fell to 60% of its nominal
value. For temperature controlled variable speed fans the situa-
tion will be different.
T able III shows the relationship between fan speed and time per
revolution at 60%, 70% and 100% of nominal rpm for fan
speeds of 1100 rpm, 2200 rpm, 4400 rpm and 8800 rpm, and
the divisor that would be used for each of these fans, based on
two tacho pulses per revolution.
T able III. Fan Speeds and Divisors
T ime per
70% Rev
(ms)
T ime per
60% Rev
(ms)
T ime per
60% Rev
(ms)
Nominal
rpm
Divisor
rpm
rpm
1
2
4
8
8800
4400
2200
1100
6.82
13.64
27.27
54.54
6160
3080
1540
770
9.74
19.48
38.96
77.92
5280
2640
1320
660
11.36
22.73
45.45
90.9
Note that Fan 1 and Fan 2 Divisors are programmed into Bits 4
to 7 of the VID0–VID3/Fan Divisor Register.
LIMIT VALUE S
Fans in general will not overspeed if run from the correct volt-
age, so the failure condition of interest is underspeed due to
electrical or mechanical failure. For this reason only low speed
limits are programmed into the limit registers for the fans. It
should be noted that, since fan period rather than speed is being
measured, a fan failure interrupt will occur when the measure-
ment exceeds the limit value.
MONIT ORING CY CLE T IME
T he monitoring cycle time depends on the fan speed and num-
ber of tacho output pulses per revolution. T wo complete periods
of the fan tacho output (three rising edges) are required for each
fan measurement. T herefore, if the start of a fan measurement
just misses a rising edge, the measurement can take almost three
tacho periods. In order to read a valid result from the fan value
registers, the total monitoring time allowed after starting the
monitoring cycle should therefore be three tacho periods of
FAN1 plus three tacho periods of FAN2 at the lowest normal
fan speed.
Although the fan monitoring cycle and the analog input moni-
toring cycle are started together, they are not synchronized in
any other way.
FAN MANUFACT URE RS
Manufacturers of cooling fans with tachometer outputs are
listed below:
NMB T ech
9730 Independence Ave.
Chatsworth, California 91311
818-341-3355
818-341-8207
Airflow
CFM
Model
Frame Size
2408NL
2410ML
3108NL
3110K L
2.36 in sq.
×
0.79 in (60 mm sq.
×
20 mm) 9–16
2.36 in sq.
×
0.98 in (60 mm sq.
×
25 mm) 14–25
3.15 in sq.
×
0.79 in (80 mm sq.
×
20 mm) 25–42
3.15 in sq.
×
0.98 in (80 mm sq.
×
25 mm) 25–40
Mechatronis Inc.
P.O. Box 613
Preston, WA 98050
800-453-4569
Models—Various sizes available with tach output option.
Sanyo Denki/K eymarc Electronics
468 Amapola Ave.
T orrance, CA 90501
310-783-5400
Models—109P Series
CHASSIS INT RUSION INPUT
T he Chassis Intrusion (CI) input is an active high input/open-
drain output intended for detection and signalling of unautho-
rized tampering with the system. An external circuit powered
from the system’s CMOS backup battery is used to detect and
latch a chassis intrusion event, whether the system is powered up
or not. Once a chassis intrusion has been detected and latched,
the CI input will generate an interrupt when the system is pow-
ered up.
T he actual detection of chassis intrusion is performed by an
external circuit that will, for example, detect when the cover has
been removed. A wide variety of techniques may be used for the
detection:
– Microswitch that opens or closes when the cover is removed.
– Reed switch operated by magnet fixed to the cover.
– Hall-effect switch operated by magnet fixed to the cover.
– Phototransistor that detects light when cover is removed.
T he chassis intrusion interrupt will remain asserted until the
external detection circuit is reset. T his can be achieved by set-
ting Bit 6 of the Configuration Register, or Bit 7 of the Chassis
Intrusion Clear Register to one, which will cause the CI pin to be
pulled low for at least 20 ms. T hese register bits are self-clearing.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM9240ARU | Low Cost Microprocessor System Hardware Monitor |
| ADM9261 | Triple- Power Supply Monitor(3路電源監視器) |
| ADM9264ARN-REEL | Quad Power Supply Monitor for Desktop PCs |
| ADM9264ARN-REEL7 | Quad Power Supply Monitor for Desktop PCs |
| ADM9264 | Quad Power Supply Monitor for Desktop PCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM9240ARU | 制造商:Analog Devices 功能描述:Data Acquisition System, 6 Channel, 9 Bit, 24 Pin, Plastic, TSSOP |
| ADM9240ARU-REEL | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost Microprocessor System Hardware Monitor |
| ADM9240ARU-REEL7 | 制造商:Analog Devices 功能描述: |
| ADM9264 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad Power Supply Monitor for Desktop PCs |
| ADM9264ARN | 制造商:Analog Devices 功能描述:Volt Supervisor Monitor 2.8V/3.3V/5V/12V 16-Pin SOIC N 制造商:Rochester Electronics LLC 功能描述:MULTI-SUPPLY HARDWARE MON - Bulk |
發布緊急采購，3分鐘左右您將得到回復。