參數資料
型號： ADAU1442YSVZ-3A-RL
廠商： Analog Devices Inc
文件頁數： 25/93頁
文件大?。?/td> 0K
描述： IC SIGMADSP 28B 175MHZ 100TQFP
標準包裝： 1,000
系列： SigmaDSP®
類型： 音頻處理器
應用： 車載音頻
安裝類型： 表面貼裝
封裝/外殼： 100-TQFP 裸露焊盤
供應商設備封裝： 100-TQFP-EP（14x14）
包裝： 帶卷 (TR)
ADAU1442/ADAU1445/ADAU1446
Data Sheet
Rev. D | Page 30 of 92
Self-Boot
On power-up, the ADAU1442/ADAU1445/ADAU1446 can
load a program and a set of parameters that are saved in an
external EEPROM. Combined with the auxiliary ADC and the
multipurpose pins, this can potentially eliminate the need for a
microcontroller in a simple audio system. The self-boot sequence
is accomplished by the ADAU1442/ADAU1445/ADAU1446
acting as masters on the I2C bus on startup, which occurs when
the SELFBOOT pin is set high. The ADAU1442/ADAU1445/
ADAU1446 cannot self-boot in SPI mode.
The maximum necessary EEPROM size is 40,960 bytes, or
40 kB. This much memory is only needed if the program RAM
(4096 × 6 bytes) and parameter RAM (4096 × 4 bytes) are each
completely full.
A self-boot operation is triggered on the rising edge of RESET
when the SELFBOOT pin is set high, and it occurs after 10 ms
when the PLL has locked. The ADAU1442/ADAU1445/
ADAU1446 read the program, parameter, and register data
from the EEPROM. After the ADAU1442/ADAU1445/ADAU1446
have finished self-booting, additional messages can be sent to the
ADAU1442/ADAU1445/ADAU1446 on the I2C bus, although
this typically is not necessary in a self-booting application. The
I2C device address for the ADAU1442/ADAU1445/ADAU1446 is
0x68 for a write and 0x69 for a read in this mode. The ADDRx pins
have different functions when the chip is in this mode; therefore,
the settings on them are ignored.
The ADAU1442/ADAU1445/ADAU1446 are masters on the I2C
bus during a self-boot operation. Care should be taken that no
other device on the I2C bus tries to perform a write operation
during self-booting. The ADAU1442/ADAU1445/ADAU1446
generate SCL at 8 × fs; therefore, when fs,NORMAL is 48 kHz, SCL
runs at 384 kHz. SCL has a duty cycle of in accordance with
the I2C specification.
Chip Address 0xA1. The LSBs of the addresses of some EEPROMs
are pin configurable; in most cases, these pins should be tied
low to set this address. SigmaStudio writes to the EEPROM at
Address 0xA0.
EEPROM Format
The EEPROM data contains a sequence of messages. Each
discrete message is one of the four types defined in Table 17.
Each message consists of a sequence of one or more bytes. The
first byte identifies the message type. Bytes are written MSB
first. Most messages are block write (0x01) types, which are
used for writing to the ADAU1442/ADAU1445/ADAU1446
program RAM, parameter RAM, and control registers.
The body of the message following the message type should
start with two bytes indicating message length and then include
a byte indicating the chip address. Following this is always a
2-byte register or memory address field, as with all other
control port transactions.
SigmaStudio is capable of generating the EEPROM data necessary
to self-boot the ADAU1442/ADAU1445/ADAU1446, using the
function called write latest compilation to E2PROM. This function
can be accessed by right-clicking the ADAU1442/ADAU1445/
ADAU1446 IC in the hardware configuration window.
Table 16. Functions of the Control Port Pins
Pin
I2C Mode
SPI Mode
Self-Boot
SCL/CCLK
SCL—input
CCLK—input
SCL—output
SDA/COUT
SDA—open collector output
COUT—output
SDA—open collector output
ADDR1/CDATA
ADDR1—input
CDATA—input
Unused input—tie to ground or power
CLATCH
Unused input—tie to ground or power
CLATCH—input
Unused input—tie to ground or power
ADDR0
ADDR0—input
Unused input—tie to ground or power
Table 17. EEPROM Message Types
Message ID
Message Type
Following Bytes
0x00
End
None
0x01
Write
One byte indicating message length (including chip address and
subaddress), one byte indicating chip address, two bytes indicating
subaddress, and an appropriate number of data bytes
0x02
Delay
Two bytes for delay
0x03
No op
None
相關PDF資料
PDF描述
ADAU1445YSVZ-3A-RL IC SIGMADSP 175MHZ 100TQFP
ADAU1461WBCPZ-R7 IC SIGMADSP 24BIT 96KHZ PLL 32
ADAU1513ACPZ-RL7 IC AMP AUDIO PWR 23W 48LFCSP
ADAU1590ACPZ-RL7 IC AMP AUDIO PWR 48LFCSP
ADAU1592ACPZ IC AMP AUDIO PWR 24W 48LFCSP
相關代理商/技術參數
參數描述
ADAU1445YSVZ-3A 功能描述:IC SIGMADSP 175MHZ 100TQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6
ADAU1445YSVZ-3A-RL 功能描述:IC SIGMADSP 175MHZ 100TQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6
ADAU1446EBZ 制造商:Analog Devices 功能描述:SIGMADSP? DIGITAL AUDIO PROCESSOR WITH FLEXIBLE AUDIO - Bulk
ADAU1446YSTZ-3A 功能描述:IC SIGMADSP 175MHZ 100LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6
ADAU1446YSTZ-3A-RL 功能描述:IC SIGMADSP 175MHZ 100LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:SigmaDSP® 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*