參數資料
型號： AD9516-5BCPZ
廠商： Analog Devices Inc
文件頁數： 21/76頁
文件大?。?/td> 0K
描述： IC CLOCK GEN W/PLL 64-LFCSP
標準包裝： 1
類型： 時鐘發生器，扇出配送
PLL： 是
輸入： CMOS，LVDS，LVPECL
輸出： CMOS，LVDS，LVPECL
電路數： 1
比率 - 輸入:輸出： 1:14
差分 - 輸入:輸出： 是/是
頻率 - 最大： 2.4GHz
除法器/乘法器： 是/無
電源電壓： 3.135 V ~ 3.465 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-VFQFN 裸露焊盤，CSP
供應商設備封裝： 64-LFCSP-VQ（9x9）
包裝： 托盤
AD9516-5
Rev. A | Page 28 of 76
Phase-Locked Loop (PLL)
CLK
CHARGE PUMP
R DIVIDER
CP
VCP
VSGND
STATUS
CPRSET
DIST
REF
RSET
DIVIDE BY
2, 3, 4, 5, OR 6
A/B
COUNTERS
LD
N DIVIDER
REFMON
0
1
0
1
P, P + 1
PRESCALER
REF2
REF1
REFERENCE
SWITCHOVER
HOLD
VCO STATUS
REF_SEL
LOCK
DETECT
STATUS
CLK
PHASE
FREQUENCY
DETECTOR
PROGRAMMABLE
N DELAY
PROGRAMMABLE
R DELAY
PLL
REF
REFIN (REF1)
REFIN (REF2)
079
72-
064
Figure 35. PLL Functional Blocks
The AD9516 includes on-chip PLL blocks that can be used with
an external VCO or VCXO to create a complete phase-locked
loop. The PLL requires an external loop filter, which usually
consists of a small number of capacitors and resistors. The
configuration and components of the loop filter help to establish
the loop bandwidth and stability of the PLL.
The AD9516 PLL is useful for generating clock frequencies from a
supplied reference frequency. This includes conversion of reference
frequencies to much higher frequencies for subsequent division
and distribution. In addition, the PLL can be exploited to clean up
jitter and phase noise on a noisy reference. The exact choices of
PLL parameters and loop dynamics are very application specific.
The flexibility and depth of the PLL allow the part to be tailored
to function in many different applications and signal environments.
Configuration of the PLL
Configuration of the PLL is accomplished by programming
the various settings for the R divider, N divider, PFD polarity,
and charge pump current. The combination of these settings
determines the PLL loop bandwidth. These are managed through
programmable register settings (see Table 47 and Table 49) and
by the design of the external loop filter. Successful PLL operation
and satisfactory PLL loop performance are highly dependent upon
proper configuration of the PLL settings.
The design of the external loop filter is crucial to the proper
operation of the PLL. A thorough knowledge of PLL theory and
design is helpful.
ADIsimCLK (V1.2 or later) is a free program that can help
with the design and exploration of the capabilities and features
of the AD9516, including the design of the PLL loop filter. It is
available at www.analog.com/clocks.
Phase Frequency Detector (PFD)
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. The PFD includes a programmable
delay element that controls the width of the antibacklash pulse.
This pulse ensures that there is no dead zone in the PFD transfer
function and minimizes phase noise and reference spurs. The
antibacklash pulse width is set by Register 0x017[1:0].
An important limit to keep in mind is the maximum frequency
allowed into the PFD, which, in turn, determines the correct anti-
backlash pulse setting. The antibacklash pulse setting is specified
in the phase/frequency detector (PFD) parameter of Table 2.
Charge Pump (CP)
The charge pump is controlled by the PFD. The PFD monitors the
phase and frequency relationship between its two inputs, and tells
the CP to pump up or pump down to charge or discharge the
integrating node (part of the loop filter). The integrated and
filtered CP current is transformed into a voltage that drives the
tuning node of the external VCO to move the VCO frequency
up or down. The CP can be set (via Register 0x010[6:4]) for high
impedance (allows holdover operation), for normal operation
(attempts to lock the PLL loop), for pump-up, or for pump-down
(test modes). The CP current is programmable in eight steps from
(nominally) 600 μA to 4.8 mA.
The exact value of the CP current LSB is set by the CPRSET
resistor, which is nominally 5.1 kΩ. If the value of the resistor
connected to the CP_RSET pin is doubled, the resulting charge
pump current range becomes 300 μA to 2.4 mA.
相關PDF資料
PDF描述
AD9517-0ABCPZ-RL7 IC CLOCK GEN 2.8GHZ VCO 48LFCSP
AD9517-1ABCPZ-RL7 IC CLOCK GEN 2.5GHZ VCO 48LFCSP
AD9517-2ABCPZ-RL7 IC CLOCK GEN 2.2GHZ VCO 48LFCSP
AD9517-3ABCPZ-RL7 IC CLOCK GEN 2.0GHZ VCO 48LFCSP
AD9517-4ABCPZ-RL7 IC CLOCK GEN 1.8GHZ VCO 48LFCSP
相關代理商/技術參數
參數描述
AD9516-5BCPZ-REEL7 功能描述:IC CLOCK GEN W/PLL 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
AD9516-5PCBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Output Clock Generator
AD9517-0A/PCBZ 功能描述:BOARD EVALUATION FOR AD9517-0A RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
AD9517-0ABCPZ 功能描述:IC CLOCK GEN 2.8GHZ VCO 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND
AD9517-0ABCPZ-RL7 功能描述:IC CLOCK GEN 2.8GHZ VCO 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*