- 您現在的位置：買賣IC網 > PDF目錄1987 > AD9516-5BCPZ (Analog Devices Inc)IC CLOCK GEN W/PLL 64-LFCSP PDF資料下載
參數資料
| 型號： | AD9516-5BCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/76頁 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GEN W/PLL 64-LFCSP |
| 標準包裝： | 1 |
| 類型： | 時鐘發生器，扇出配送 |
| PLL： | 是 |
| 輸入： | CMOS，LVDS，LVPECL |
| 輸出： | CMOS，LVDS，LVPECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:14 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 2.4GHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
AD9516-5
Rev. A | Page 26 of 76
Table 19. Settings for Using an Internal PLL with an External
VCO < 1600 MHz
Register
Description
0x1E1[0] = 1b
Bypass the VCO divider as source for
distribution section
0x010[1:0] = 00b
PLL normal operation (PLL on) along with other
appropriate PLL settings in Register 0x010 to
Register 0x01E
An external VCO/VCXO requires an external loop filter that
must be connected between CP and the tuning pin of the VCO/
VCXO. This loop filter determines the loop bandwidth and
stability of the PLL. Ensure that the correct PFD polarity is
selected for the VCO/VCXO that is being used.
Table 20. Setting the PFD Polarity
Register
Description
0x010[7] = 0b
PFD polarity positive (higher control voltage
produces higher frequency)
0x010[7] = 1b
PFD polarity negative (higher control voltage
produces lower frequency)
After the appropriate register values are programmed,
Register 0x232 must be set to 0x01 for the values to take effect.
Mode 2 (High Frequency Clock Distribution)—CLK or
External VCO > 1600 MHz
The AD9516 power-up default configuration has the PLL
powered off and the routing of the input set so that the CLK/
CLK input is connected to the distribution section through the
VCO divider (divide-by-2/divide-by-3/divide-by-4/divide-by-5/
divide-by-6). This is a distribution-only mode that allows for an
external input of up to 2400 MHz (see Table 4). For divide ratios
other than 1, the maximum frequency that can be applied to the
channel dividers is 1600 MHz. Therefore, the VCO divider must
be used to divide down input frequencies that are greater than
1600 MHz before the channel dividers can be used for further
division. This input routing can also be used for lower input
frequencies, but the minimum divide is 2 before the channel
dividers.
When the PLL is enabled, this routing also allows the use of
the PLL with an external VCO or VCXO with a frequency of
<2400 MHz. In this configuration, the external VCO/VCXO
feeds directly into the prescaler.
The register settings shown in Table 21 are the default values
of these registers at power-up or after a reset operation. If the
contents of the registers are altered by prior programming after
power-up or reset, these registers can also be set intentionally to
these values.
Table 21. Default Settings of Some PLL Registers
Register
Description
0x010[1:0] = 01b
PLL asynchronous power-down (PLL off ).
0x1E0[2:0] = 010b
Set VCO divider = 4.
0x1E1[0] = 0b
Use the VCO divider.
When using the internal PLL with an external VCO, the PLL
must be turned on.
Table 22. Settings When Using an External VCO
Register
Description
0x010[1:0] = 00b
PLL normal operation (PLL on).
0x010 to 0x01D
PLL settings. Select and enable a reference
input. Set R, N (P, A, B), PFD polarity, and ICP
according to the intended loop configuration.
0x1E1[1] = 0b
CLK selected as the source.
An external VCO requires an external loop filter that must be
connected between CP and the tuning pin of the VCO. This loop
filter determines the loop bandwidth and stability of the PLL.
Ensure that the correct PFD polarity is selected for the VCO
that is being used.
Table 23. Setting the PFD Polarity
Register
Description
0x010[7] = 0b
PFD polarity positive (higher control
voltage produces higher frequency).
0x010[7] = 1b
PFD polarity negative (higher control
voltage produces lower frequency).
After the appropriate register values are programmed,
Register 0x232 must be set to 0x01 for the values to take effect.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9517-0ABCPZ-RL7 | IC CLOCK GEN 2.8GHZ VCO 48LFCSP |
| AD9517-1ABCPZ-RL7 | IC CLOCK GEN 2.5GHZ VCO 48LFCSP |
| AD9517-2ABCPZ-RL7 | IC CLOCK GEN 2.2GHZ VCO 48LFCSP |
| AD9517-3ABCPZ-RL7 | IC CLOCK GEN 2.0GHZ VCO 48LFCSP |
| AD9517-4ABCPZ-RL7 | IC CLOCK GEN 1.8GHZ VCO 48LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9516-5BCPZ-REEL7 | 功能描述:IC CLOCK GEN W/PLL 64-LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| AD9516-5PCBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Output Clock Generator |
| AD9517-0A/PCBZ | 功能描述:BOARD EVALUATION FOR AD9517-0A RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| AD9517-0ABCPZ | 功能描述:IC CLOCK GEN 2.8GHZ VCO 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND |
| AD9517-0ABCPZ-RL7 | 功能描述:IC CLOCK GEN 2.8GHZ VCO 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。