參數資料
型號： AD9239BCPZ-170
廠商： Analog Devices Inc
文件頁數： 24/40頁
文件大小： 0K
描述： IC ADC 12BIT DUAL 170MSPS 72PIN
標準包裝： 1
位數： 12
采樣率（每秒）： 170M
數據接口： 串行，SPI?
轉換器數目： 4
功率耗散（最大）： 1.22W
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 72-VFQFN 裸露焊盤，CSP
供應商設備封裝： 72-LFCSP
包裝： 托盤
輸入數目和類型： 8 個單端，單極；4 個差分，單極
AD9239
Data Sheet
Rev. C | Page 30 of 40
TEMPOUT Pin
The TEMPOUT pin can be used as a course temperature sensor
to monitor the internal die temperature of the device. This pin
typical has a 734 mV output with a clock rate of 250 MSPS and
a negative temperature going coefficient of 1.12 mV/C. The
voltage response of this pin is characterized in Figure 76.
0.85
0.83
0.81
0.79
0.77
0.75
0.73
0.71
0.69
0.67
0.65
–40 –30 –20 –10
0
10
20
30
40
50
60
70
80
TEMPERATURE (°C)
T
EMPO
U
T
PI
N
VO
L
T
A
G
E
(V)
06980-
055
Figure 76. TEMPOUT Pin Voltage vs. Temperature
RBIAS Pin
To set the internal core bias current of the ADC, place a resistor
(nominally equal to 10.0 k) between ground and the RBIAS pin.
The resistor current is derived on chip and sets the AVDD current
of the ADC to a nominal 725 mA at 250 MSPS. Therefore, it is
imperative that a 1% or less tolerance on this resistor be used to
achieve consistent performance.
VCMx Pins
The common-mode output pins can be enabled through the SPI
to provide an external reference bias voltage of 1.4 V for driving the
VIN + x/VIN x analog inputs. These pins may be required when
connecting external devices, such as an amplifier or transformer,
to interface to the analog inputs.
RESET Pin
The RESET pin sets all SPI registers to their default values and
the datapath. Using this pin requires the user to resync the
digital outputs. This pin is only 1.8 V tolerant.
PDWN Pin
When asserted high, the PDWN pin turns off all the ADC
channels, including the output drivers. This function can be
changed to a standby function. See Register 8 in Table 15. Using
this feature allows the user to put all channels into standby mode.
The output drivers transmit pseudorandom data until the outputs
are disabled using Register 14.
By asserting the PDWN pin high, the AD9239 is placed into
power-down mode, shutting down the reference, reference buffer,
PLL, and biasing networks. In this state, the ADC typically
dissipates 3 mW. If any of the SPI features are changed before
the power-down feature is enabled, the chip continues to function
after PDWN is pulled low without requiring a reset. The AD9239
returns to normal operating mode when the PDWN pin is pulled
low. This pin is only 1.8 V tolerant.
SDO Pin
The SDO pin is for use in applications that require a 4-wire SPI
mode operation. For normal operation, it should be tied low to
AGND through a 10 k resistor. Alternatively, the device pin
can be left open, and the 345 internal pull-down resistor pulls
this pin low. This pin adheres to only 1.8 V logic.
SDI/SDIO Pin
The SDI/SDIO pin is for use in applications that require either a
4- or 3-wire SPI mode operation. For normal operation, it should
be tied low to AGND through a 10 k resistor. Alternatively,
the device pin can be left open, and the 30 k internal pull-
down resistor pulls this pin low. This pin is only 1.8 V tolerant.
SCLK Pin
For normal operation, the SCLK pin should be tied to AGND
through a 10 k resistor. Alternatively, the device pin can be left
open, and the 30 k internal pull-down resistor pulls this pin low.
This pin is only 1.8 V tolerant.
CSB Pin
For normal operation, the CSB pin should be tied high to
AVDD through a 10 k resistor. Alternatively, the device pin
can be left open, and the 26 k internal pull-up resistor pulls
this pin high. By tying the CSB pin to AVDD, all SCLK and
SDI/SDIO information is ignored. In comparison, by tying the
CSB pin low, all information on the SDO and SDI/SDIO pins
are written to the device. This feature allows the user to reduce
the number of traces to the device if necessary. This pin is only
1.8 V tolerant.
PGMx Pins
All PGMx pins are automatically initialized as a sync pin by
default. These pins are used to lock the FPGA timing and data
capture during initial startup. These pins are respective to each
channel (PGM3 = Channel A). The sync pin should be pulled
low until this pin receives a high signal input from the receiver,
during which time the ADC outputs a training word. The training
word defaults to the values implemented by the user in Register 19
through Register 20. When the receiver finds the frame boundary,
the sync identification is deasserted high and the ADC outputs
the valid data on the next packet boundary.
Once steady state operation for the device has occurred, these
pins can be assigned as a standby option using Register 53 in
Table 15. All other pins change to a global sync pin.
This pin is only 1.8 V tolerant.
相關PDF資料
PDF描述
AD9240AS IC ADC 14BIT 10MSPS 44-MQFP
AD9241ASZRL IC ADC 14BIT SGL 1.25MSPS 44MQFP
AD9243ASZRL IC ADC 14BIT SGL 3MSPS 44MQFP
AD9244BSTZRL-65 IC ADC 14BIT SGL 65MSPS 48LQFP
AD9245BCPZRL7-80 IC ADC 14BIT SGL 80MSPS 32LFCSP
相關代理商/技術參數
參數描述
AD9239BCPZ-210 功能描述:模數轉換器 - ADC Quad 12 Bit 210 MSPS Serial ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD9239BCPZ-250 功能描述:模數轉換器 - ADC Quad 12 Bit 250 MSPS Serial ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD9240 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete 14-Bit, 10 MSPS Monolithic A/D Converter
AD9240AS 功能描述:IC ADC 14BIT 10MSPS 44-MQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9240ASRL 功能描述:IC ADC 14BIT 10MSPS 44-MQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*