- 您現在的位置：買賣IC網 > PDF目錄9737 > AD7148ACPZ-1500RL7 (Analog Devices Inc)IC CAP-TO-DGTL CONV PROG 16LFCSP PDF資料下載
參數資料
| 型號： | AD7148ACPZ-1500RL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/57頁 |
| 文件大小： | 0K |
| 描述： | IC CAP-TO-DGTL CONV PROG 16LFCSP |
| 標準包裝： | 1 |
| 類型： | 電容性 |
| 觸摸面板接口： | 2 線 |
| 輸入數/鍵： | 8 鍵 |
| 分辨率（位）： | 16 b |
| 數據接口： | I²C，串行 |
| 數據速率/采樣率 (SPS，BPS)： | 250k |
| 電壓基準： | 內部 |
| 電源電壓： | 2.6 V ~ 3.3 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 16-LFCSP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 781 (CN2011-ZH PDF) |
| 其它名稱： | AD7148ACPZ-1500RL7DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
AD7148
Rev. A | Page 26 of 56
INTERRUPT OUTPUT
The AD7148 has an interrupt output that triggers an interrupt
service routine on the host processor. The INT signal is on
Pin 12 and is an open-drain output. There are two types of
interrupt events on the AD7148: a CDC conversion complete
interrupt and a sensor threshold interrupt. Each interrupt has
enable and status registers. The conversion complete and sensor
threshold interrupts can be enabled on a per conversion stage
basis. The status registers indicate what type of interrupt triggered
the INT pin. Status registers are cleared, and the INT signal is
reset high during a read operation. The signal returns high as
soon as the read address is set up.
CDC CONVERSION-COMPLETE INTERRUPT
The AD7148 interrupt signal asserts low to indicate the
completion of a conversion stage, and new conversion result
data is available in the registers.
The interrupt can be independently enabled for each conversion
stage. Each conversion-stage-complete interrupt can be enabled
via the STAGEx_COMPLETE_INT_EN register (Address 0x007).
This register has a bit that corresponds to each conversion stage.
Setting this bit to 1 enables the interrupt for that stage. Clearing this
bit to 0 disables the conversion complete interrupt for that stage.
In normal operation, the interrupt is enabled only for the last stage
in a conversion sequence. For example, if there are five conversion
stages, the conversion-complete interrupt for STAGE4 is enabled.
INT asserts only when all five conversion stages are complete, and
the host can read new data from all five results registers. The inter-
rupt is cleared by reading the STAGEx_COMPLETE_INT_
STATUS register located at Address 0x00A.
Register 0x00A is the conversion-complete interrupt status register.
Each bit in this register corresponds to a conversion stage. If a
bit is set, it means that the conversion-complete interrupt for
the corresponding stage has been triggered. This register is
cleared on a read, provided that the underlying condition that
triggered the interrupt has gone away.
SENSOR TOUCH INTERRUPT
The sensor touch interrupt mode is implemented when the host
processor requires an interrupt only when a sensor is contacted.
Configuring the AD7148 into this mode results in the interrupt
being asserted when the user makes contact with the sensor and
again when the user lifts off the sensor. The second interrupt is
required to alert the host processor that the user is no longer
contacting the sensor.
The registers located at Address 0x005 (STAGEx_LOW_INT_EN)
and Address 0x006 (STAGEx_HIGH_INT_EN) are used to enable
the interrupt output for each stage. The registers located at
Address 0x008 (STAGEx_LOW_LIMIT_INT) and Address 0x009
(STAGEx_HIGH_LIMIT_INT) are used to read back the interrupt
status for each stage.
Figure 36 shows the interrupt output timing during contact with
one of the sensors connected to STAGE0 while operating in the
sensor touch interrupt mode. For a low limit configuration, the
interrupt output is asserted as soon as the sensor is contacted and
again after the user has stopped contacting the sensor.
Note that the interrupt output remains low until the host processor
reads back the interrupt status registers located at Address 0x008
and Address 0x009.
The interrupt output is asserted when there is a change in the
threshold status bits. This change indicates that a user is now
touching the sensor(s) for the first time, the number of sensors
being touched has changed, or the user is no longer touching
the sensor(s). Reading the status bits in the interrupt status
register shows the current sensor activations.
4
2
CONVERSION
STAGE
SERIAL
READBACK
NOTES:
1. USER TOUCHING DOWN ON SENSOR
2. ADDRESS 0x008 READ BACK TO CLEAR INTERRUPT
3. USER LIFTING OFF OF SENSOR
4. ADDRESS 0x008 READ BACK TO CLEAR INTERRUPT
STAGE0
STAGE1
INT OUTPUT
071
55
-03
5
Figure 36. Example of Sensor Touch Interrupt
相關PDF資料 |
PDF描述 |
|---|---|
| MS27467P9B98SA | CONN PLUG 3POS STRAIGHT W/SCKT |
| VE-J1J-MX-F1 | CONVERTER MOD DC/DC 36V 75W |
| MS27484T10B35PB | CONN PLUG 13POS STRAIGHT W/PINS |
| SY100E416JI | IC LINE RCVR QUINT DIFF 28-PLCC |
| MS27467T15F19PD | CONN PLUG 19POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7148ACPZ-1REEL | 功能描述:IC CAP-TO-DGTL CONV PROG 16LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7150 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra Low Power, 2 Channel, Capacitance Converter for Proximity Sensing |
| AD7150BRMZ | 功能描述:IC CAP CONV 2CH ULT LP 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD7150BRMZ-REEL | 功能描述:IC CAP CONV 2CH ULT LP 10MSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD7151 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Ultra-Low Power, 1-Channel, Capacitance Converter for Proximity Sensing |
發布緊急采購，3分鐘左右您將得到回復。