- 您現在的位置：買賣IC網 > PDF目錄11786 > AD6641BCPZ-500 (Analog Devices Inc)IC IF RCVR 11BIT 200MSPS 56LFCSP PDF資料下載
參數資料
| 型號： | AD6641BCPZ-500 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC IF RCVR 11BIT 200MSPS 56LFCSP |
| 標準包裝： | 1 |
| 應用： | 無線通信系統 |
| 接口： | CMOS，LVDS，并聯， 串行，SPI |
| 電源電壓： | 1.8 V ~ 2 V |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 56-LFCSP-VQ（8x8） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD6641
Rev. 0 | Page 27 of 28
ANALOG INPUT AND VOLTAGE REFERENCE
The analog input to the AD6641 is a differential buffer. For
best dynamic performance, match the source impedances
driving VIN+ and VIN such that common-mode settling
errors are symmetrical. The analog input is optimized to provide
superior wideband performance and requires that the analog
inputs be driven differentially. SNR and SINAD performance
degrades significantly if the analog input is driven with a single-
ended signal.
A wideband transformer, such as Mini-Circuits ADT1-1WT,
can provide the differential analog inputs for applications that
require a single-ended-to-differential conversion. Both analog
inputs are self-biased by an on-chip reference to a nominal 1.7 V.
An internal differential voltage reference creates positive and
negative reference voltages that define the 1.5 V p-p fixed span
of the ADC core. This internal voltage reference can be adjusted
by means of an SPI control.
VREF
The AD6641 VREF pin (Pin 31) allows the user to monitor the
on-board voltage reference or provide an external reference
(requires configuration through the SPI). The three optional
settings are internal VREF (pin is connected to 20 kΩ to ground),
export VREF, and import VREF. Do not attach a bypass capacitor
to this pin. VREF is internally compensated and additional
loading may impact performance.
CONFIGURATION USING THE SPI
Three pins define the SPI of the AD6641: SCLK, SDIO, and CSB
(see Table 11). SCLK (a serial clock) is used to synchronize the
read and write data presented from and to the AD6641. SDIO
(serial data input/output) is a bidirectional pin that allows data
to be sent to and read from the internal memory map registers.
CSB (chip select) is an active low control that enables or disables
the read and write cycles.
Table 11. Serial Port Interface Pins
Pin
Function
SCLK
Serial clock. Serial shift clock input. SCLK is used to
synchronize serial interface reads and writes.
SDIO
Serial data input/output. Bidirectional pin that serves
as an input or an output, depending on the instruction
being sent and the relative position in the timing frame.
CSB
Chip select (active low). This control gates the read and
write cycles.
The falling edge of the CSB pin, in conjunction with the rising
edge of the SCLK pin, determines the start of the framing. An
example of the serial timing can be found in Figure 43 (for
symbol definitions, see Table 5).
CSB can be held low indefinitely, which permanently enables
the device; this is called streaming. CSB can stall high between
bytes to allow additional external timing. When CSB is tied
high, SPI functions are placed in high impedance mode.
During an instruction phase, a 16-bit instruction is transmitted.
The first bit of the first byte in a serial data transfer frame indicates
whether a read command or a write command is issued. Data
follows the instruction phase, and its length is determined by
the W0 and W1 bits. All data is composed of 8-bit words.
The instruction phase determines whether the serial frame is a
read or write operation, allowing the serial port to be used both
to program the chip and to read the contents of the on-chip
memory. If the instruction is a read operation, the serial data
input/output (SDIO) pin changes direction from an input to an
output at the appropriate point in the serial frame.
Data can be sent in MSB first mode or in LSB first mode. MSB
first is the default mode on power-up and can be changed via
the SPI port configuration register. For more information about
this and other features, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
DON’T CARE
DON’T
CARE
DON’T
CARE
SDIO
SCLK
CSB
tS
tDH
tCLK
tDS
tH
R/W
W1
W0
A12
A11
A10
A9
A8A7
D5D4D3
D2
D1D0
tLOW
tHIGH
098
13
-0
73
Figure 43. Serial Port Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| VI-JTJ-IW-F3 | CONVERTER MOD DC/DC 36V 100W |
| VI-JTJ-IW-F2 | CONVERTER MOD DC/DC 36V 100W |
| 1604037-4 | CONN HOUSING POWER 2POLE BATTERY |
| VI-JTH-IW-F4 | CONVERTER MOD DC/DC 52V 100W |
| 647845-3 | CONN HOUSING PWR SER 50 2POS RED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD6641BCPZRL7-500 | 功能描述:IC IF RCVR 11BIT 200MSPS 56LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD6642 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual IF Receiver |
| AD6642BBCZ | 功能描述:IC IF RCVR 11BIT 200MSPS 144BGA RoHS:是 類別:RF/IF 和 RFID >> RF 其它 IC 和模塊 系列:- 標準包裝:100 系列:* |
| AD6642BBCZRL | 功能描述:IC IF RCVR 11BIT 200MSPS 144BGA RoHS:是 類別:RF/IF 和 RFID >> RF 其它 IC 和模塊 系列:- 標準包裝:100 系列:* |
| AD6642EBZ | 功能描述:BOARD EVALUATION FOR AD6642 RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796 |
發布緊急采購，3分鐘左右您將得到回復。