Revision 13 2-9 Power Calculation Methodology This section describes a simplified method to estimate power consumptio" />
參數資料
型號： A3PE-STARTER-KIT-2
廠商： Microsemi SoC
文件頁數： 79/162頁
文件大?。?/td> 0K
描述： KIT EVAL FOR A3PE1500 PROASIC3
產品變化通告： Kit/Part Number Change 25/Jul/2012
標準包裝： 1
系列： ProASIC3
類型： FPGA
適用于相關產品： A3PE1500
所含物品： 板，電源，編程器
其它名稱： 1100-1144
A3PE-STARTER-KIT
ProASIC3E Flash Family FPGAs
Revision 13
2-9
Power Calculation Methodology
This section describes a simplified method to estimate power consumption of an application. For more
accurate and detailed power estimations, use the SmartPower tool in the Libero SoC software.
The power calculation methodology described below uses the following variables:
The number of PLLs as well as the number and the frequency of each output clock generated
The number of combinatorial and sequential cells used in the design
The internal clock frequencies
The number and the standard of I/O pins used in the design
The number of RAM blocks used in the design
Toggle rates of I/O pins as well as VersaTiles—guidelines are provided in Table 2-11 on
Enable rates of output buffers—guidelines are provided for typical applications in Table 2-12 on
Read rate and write rate to the memory—guidelines are provided for typical applications in
Table 2-12 on page 2-11. The calculation should be repeated for each clock domain defined in the
design.
Methodology
Total Power Consumption—PTOTAL
PTOTAL = PSTAT + PDYN
PSTAT is the total static power consumption.
PDYN is the total dynamic power consumption.
Total Static Power Consumption—PSTAT
PSTAT = PDC1 + NINPUTS * PDC2 + NOUTPUTS * PDC3
NINPUTS is the number of I/O input buffers used in the design.
NOUTPUTS is the number of I/O output buffers used in the design.
Total Dynamic Power Consumption—PDYN
PDYN = PCLOCK + PS-CELL + PC-CELL + PNET + PINPUTS + POUTPUTS + PMEMORY + PPLL
Global Clock Contribution—PCLOCK
PCLOCK = (PAC1 + NSPINE * PAC2 + NROW * PAC3 + NS-CELL * PAC4) * FCLK
NSPINE is the number of global spines used in the user design—guidelines are provided in the
"Spine Architecture" section of the Global Resources chapter in the ProASIC3E FPGA Fabric
.
NROW is the number of VersaTile rows used in the design—guidelines are provided in the
"Spine Architecture" section of the Global Resources chapter in the ProASIC3E FPGA Fabric
.
FCLK is the global clock signal frequency.
NS-CELL is the number of VersaTiles used as sequential modules in the design.
PAC1, PAC2, PAC3, and PAC4 are device-dependent.
Sequential Cells Contribution—PS-CELL
PS-CELL = NS-CELL * (PAC5 + 1 / 2 * PAC6) * FCLK
NS-CELL is the number of VersaTiles used as sequential modules in the design. When a
multi-tile sequential cell is used, it should be accounted for as 1.
1 is the toggle rate of VersaTile outputs—guidelines are provided in Table 2-11 on
.
FCLK is the global clock signal frequency.
相關PDF資料
PDF描述
0210490279 CABLE JUMPER 1.25MM .051M 22POS
EBM22DCMD-S288 CONN EDGECARD 44POS .156 EXTEND
ECA14DRMI-S288 CONN EDGECARD 28POS .125 EXTEND
0210490905 CABLE JUMPER 1.25MM .102M 21POS
MPC8377E-RDBA BOARD REF DES MPC8377 REV 2.1
相關代理商/技術參數
參數描述
A3PFA1X201J1 制造商:APEM 功能描述:Pushbutton,A3,latching,12V,red
A3PFA1X201J2 制造商:APEM 功能描述:Pushbutton,latching,12V,green
A3PFA1X201J3 制造商:APEM 功能描述:Pushbutton,latching,12V,amber
A3PFA1X201J4 制造商:APEM 功能描述:Pushbutton,A3,latching,12V,blue
A3PFA1X201K1 制造商:APEM 功能描述:Pushbutton,A3,latching 24V,red
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*