參數資料
型號: 908E625
廠商: 飛思卡爾半導體(中國)有限公司
英文描述: Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
中文描述: 綜合四半僅符合電源橋,嵌入式微控制器和LIN串行通信
文件頁數: 40/48頁
文件大?。?/td> 615K
代理商: 908E625
Analog Integrated Circuit Device Data
Freescale Semiconductor
40
908E625
FUNCTIONAL DEVICE OPERATION
FACTORY TRIMMING AND CALIBRATION
Autonomous Watchdog Rate Bit (AWDR)
This read/write bit selects the clock rate of the
Autonomous Watchdog. Reset clears the AWDR bit.
1 = Fast rate selected (10 ms)
0 = Slow rate selected (20 ms)
VOLTAGE REGULATOR
The 908E625 chip contains a low-power, low-drop voltage
regulator to provide internal power and external power for the
MCU. The on-chip regulator consist of two elements, the
main voltage
regulator and the low-voltage reset circuit.
The V
DD
regulator accepts a unregulated input supply and
provides a regulated V
DD
supply to all digital sections of the
device. The output of the regulator is also connected to the
VDD terminal to provide the 5.0 V to the microcontroller.
RUN Mode
During RUN mode the main voltage regulator is on. It
provides a regulated supply to all digital sections.
STOP Mode
During STOP mode the STOP mode regulator supplies a
regulated output voltage. The STOP mode regulator has a
very limited output current capability. The output voltage will
be lower than the output voltage of the main voltage
regulator.
FACTORY TRIMMING AND CALIBRATION
To enhance the ease-of-use of the 908E625, various
parameters (e.g. ICG trim value) are stored in the flash
memory of the device. The following flash memory locations
are reserved for this purpose and might have a value different
from the
empty
(0xFF) state:
0xFD80:0xFDDF Trim and Calibration Values
0xFFFE:0xFFFF Reset Vector
In the event the application uses these parameters, one
has to take care not to erase or override these values. If these
parameters are not used, these flash locations can be erased
and otherwise used.
Trim Values
Below the usage of the trim values located in the flash
memory is explained
Internal Clock Generator (ICG) Trim Value
The internal clock generator (ICG) module is used to
create a stable clock source for the microcontroller without
using any external components. The untrimmed frequency of
the low-frequency base clock (IBASE), will vary as much as
±25 percent due to process, temperature, and voltage
dependencies. To compensate this dependancies a ICG trim
values is located at adress $FDC2. After trimming the ICG is
a range of typ. ±2% (±3% max.) at nominal conditions (filtered
(100nF) and stabilized (4,7uF) V
DD
= 5V, T
Ambient
~25°C) and
will vary over temperature and voltage (VDD) as indicated in
the 68HC908EY16 datasheet.
To trim the ICG this values has to be copied to the ICG
Trim Register ICGTR at adress $38 of the MCU.
Important
The value has to copied after every reset.
相關PDF資料
PDF描述
908E626 Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908JKJK3JL3FS 68HC908JK1/JK3/JL3 8-Bit Microcontroller
909-0010 PUNCH 9 WAY D REAR MOUNT
909-0020 PUNCH 15 WAY D REAR MOUNT
909-0030 PUNCH 25 WAY D REAR MOUNT
相關代理商/技術參數
參數描述
908E625_07 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
908E625_10 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
908E626 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_09 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication