- 您現在的位置：買賣IC網 > PDF目錄360557 > 908E625 (飛思卡爾半導體(中國)有限公司) Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication PDF資料下載
參數資料
| 型號： | 908E625 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 中文描述： | 綜合四半僅符合電源橋，嵌入式微控制器和LIN串行通信 |
| 文件頁數： | 30/48頁 |
| 文件大?。?/td> | 615K |
| 代理商： | 908E625 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
30
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Figure 15. Hall-Effect Sensor Input Terminal Connected to Three-Terminal Hall-Effect Sensor
Interrupts
The Hall-effect sensor input terminals are interrupt
capable. How and when an interrupt occurs is dependent on
the operating mode, RUN or Stop.
RUN Mode
In RUN mode the Hall-effect sensor input terminal interrupt
flag (HPF) will be set if a state change on the hallflags (HxF)
is detected. The interrupt is maskable with the HPIE bit in the
Interrupt Mask Register. Before enabling the interrupt, the
flag should be cleared in order to prevent a wrong interrupt.
STOP Mode
In STOP mode the Hall-effect sensor input terminals are
disabled independent of the state of the HxEN flags.
CYCLIC WAKE-UP
The Hall-effect sensor inputs can be used to wake up the
system. This wake-up function is provided by the cyclic check
wake-up feature of the AWD (Autonomous Watchdog).
If the cyclic check wake-up feature is enabled (AWDCC bit
is set), the AWD switches on the enabled Hall-effect sensor
terminals periodically. To ensure that the Hall-effect sensor
current is stabilized after switching on, the inputs are sensed
after ~40
μ
s. If a 1 is detected (I
Hall sensor
> I
HSCT
) and the
interrupt mask bit HPIE is set, an interrupt is performed.
This
wakes up the MCU and starts the main voltage regulator.
The wake-up function via this input is available when all
three conditions exist:
The two-terminal Hall-effect sensor input is enabled
(HxEN = 1)
The cyclic wake-up of the AWD is enabled (AWDCC =
1); see
Figure 16
The Hall-effect sensor input terminal interrupt is
enabled (HPIE = 1)
HxEN
HxF
Sense
Circuitry
V
Hx
GND
Three-Terminal Hall-Effect Sensor
Out
Vs
GND
相關PDF資料 |
PDF描述 |
|---|---|
| 908E626 | Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 908JKJK3JL3FS | 68HC908JK1/JK3/JL3 8-Bit Microcontroller |
| 909-0010 | PUNCH 9 WAY D REAR MOUNT |
| 909-0020 | PUNCH 15 WAY D REAR MOUNT |
| 909-0030 | PUNCH 25 WAY D REAR MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 908E625_07 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 908E625_10 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication |
| 908E626 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 908E626_08 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| 908E626_09 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
發布緊急采購，3分鐘左右您將得到回復。