參數資料
型號： 908E625
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
中文描述： 綜合四半僅符合電源橋，嵌入式微控制器和LIN串行通信
文件頁數： 39/48頁
文件大?。?/td> 615K
代理商： 908E625
Analog Integrated Circuit Device Data
Freescale Semiconductor
39
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Overtemperature Status Bit (HTF)
This read-only bit is a copy of the HTF bit in the Interrupt
Flag Register.
1 = Overtemperature condition has occurred
0 = No overtemperature condition has occurred
AUTONOMOUS WATCHDOG (AWD)
The Autonomous Watchdog module consists of three
functions:
Watchdog function for the CPU in RUN mode
Periodic interrupt function in STOP mode
Cyclic wake-up function in STOP mode
The AWD is enabled if AWDIE, AWDRE, or AWDCC in the
AWDCTL Register is set. If these bits are cleared, the AWD
oscillator is disabled and the watchdog switched off.
WATCHDOG
The watchdog function is only available in RUN mode. On
setting the AWDRE bit, watchdog functionality in RUN mode
is activated. Once this function is enabled, it is not possible to
disable it via software.
If the timer reaches end value and AWDRE is set, a
system reset is
initiated. Operations of the watchdog function
cease in STOP mode. Normal operation will be continued
when the system is back to RUN mode.
To prevent a watchdog reset, the watchdog timeout
counter must be reset before it reaches the end value. This is
done by a write to the AWDRST bit in the AWDCTL Register.
PERIODIC INTERRUPT
Periodic interrupt is
only
available in STOP mode. It is
enabled by setting the AWDIE bit in the AWDCTL Register. If
AWDIE is set, the AWD wakes up the system after a fixed
period of time. This time period can be selected with bit
AWDR in the AWDCTL Register.
CYCLIC WAKE-UP
The cyclic wake-up feature is only available in STOP
mode. If this feature is enabled, the selected Hall-effect
sensor input terminals are switched on and sensed. If a “1” is
detected on one of these inputs and the interrupt for the Hall-
effect sensors is enabled, a system wake-up is performed.
(Switch on main voltage regulator and assert
IRQ_A
to the
microcontroller).
AUTONOMOUS WATCHDOG CONTROL
REGISTER (AWDCTL)
Autonomous Watchdog Reset Bit (AWDRST)
This write-only bit resets the Autonomous Watchdog
timeout period. AWDRST always reads 0. Reset clears
AWDRST bit.
1 = Reset AWD and restart timeout period
0 = No effect
Autonomous Watchdog Reset Enable Bit (AWDRE)
This read/write bit enables resets on AWD time-outs. A
reset on the
RST_A
is only asserted when the device is in
RUN mode. AWDRE is one-time setable (write once) after
each reset. Reset clears the AWDRE bit.
1 = Autonomous watchdog enabled
0 = Autonomous watchdog disabled
Autonomous Watchdog Interrupt Enable Bit (AWDIE)
This read/write bit enables CPU interrupts by the
Autonomous Watchdog timeout flag, AWFD.
IRQ_A
is only
asserted when the device is in STOP mode. Reset clears the
AWDIE bit.
1 = CPU interrupt requests from AWDF enabled
0 = CPU interrupt requests from AWDF disabled
Autonomous Watchdog Cyclic Check (AWDCC)
This read/write bit enables the cyclic check of the two-
terminal Hall-effect sensor and the analog inputs. Reset
clears the AWDCC bit.
1 = Cyclic check of the Hall-effect sensor and analog
port
0 = No cyclic check of the Hall-effect sensor and analog
port
Autonomous Watchdog Timeout Flag Bit (AWDF)
This read/write flag is set when the Autonomous
Watchdog has timed out. Clear AWDF by writing a Logic [1]
to AWDF. Clearing AWDF also resets the AWD counter and
starts a new timeout period. Reset clears the AWDF bit.
Writing a Logic [0] to AWDF has no effect.
1 = AWD has timed out
0 = AWD has not yet timed out
Register Name and Address: AWDCTL - $0a
Bits
7
6
5
4
3
2
1
0
Read
0
0
0
AWDR
E
AWDI
E
AWDC
C
AWDF
AWD
R
Write
AWDRS
T
Reset
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
908E626 Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908JKJK3JL3FS 68HC908JK1/JK3/JL3 8-Bit Microcontroller
909-0010 PUNCH 9 WAY D REAR MOUNT
909-0020 PUNCH 15 WAY D REAR MOUNT
909-0030 PUNCH 25 WAY D REAR MOUNT
相關代理商/技術參數
參數描述
908E625_07 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
908E625_10 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
908E626 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_09 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*