參數資料
型號： 908E625
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
中文描述： 綜合四半僅符合電源橋，嵌入式微控制器和LIN串行通信
文件頁數： 38/48頁
文件大?。?/td> 615K
代理商： 908E625
Analog Integrated Circuit Device Data
Freescale Semiconductor
38
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
SYSTEM CONTROL REGISTER (SYSCTL)
Power Stages On Bit (PSON)
This read/write bit enables the power stages (half-bridges,
high side, LIN transmitter, Analog Input PA1 current sources,
and HVDD output). Reset clears the PSON bit.
1 = Power stages enabled.
0 = Power stages disabled.
LIN Slew Rate Selection Bits (SRS0:SRS1)
These read/write bits enable the user to select the
appropriate LIN slew rate for different baud rate
configurations as shown in
Table 11
.
The high speed slew rates are used, for example, for
programming via the LIN and are not intended for use in the
application.
Go to STOP Mode Bit (GS)
This write-only bit instructs the 908E625 to power down
and go into STOP mode.
Reset or CPU interrupt requests
clear the GS bit.
1 = Power down and go into STOP mode
0 = Not in STOP mode
SYSTEM STATUS REGISTER (SYSSTAT)
Hall-Effect Sensor Input Terminal Overcurrent Flag Bit
(HP_OCF)
This read/write flag is set on an overcurrent condition at
one of the Hall-effect sensor input terminals. Clear HP_OCF
and enable the output by writing a Logic [1] to the HP_OCF
flag. Reset clears the HP_OCF bit. Writing a Logic [0] to
HP_OCF has no effect.
1 = Overcurrent condition on Hall-effect sensor input
terminal has occurred
0 = No overcurrent condition on Hall-effect sensor input
terminal has occurred
LIN Current Limitation Bit (LINCL)
This read-only bit is set if the LIN transmitter operates in
current limitation region. Due to excessive power dissipation
in the transmitter, software is advised to turn the transmitter
off immediately.
1 = Transmitter operating in current limitation region
0 = Transmitter not operating in current limitation region
HVDD Output Overcurrent Flag Bit (HVDD_OCF)
This read/write flag is set on an overcurrent condition at
the HVDD terminal. Clear HVDD_OCF and enable the output
by writing a Logic [1] to the HVDD_OCF Flag. Reset clears
the HVDD_OCF bit. Writing a Logic [0] to HVDD_OCF has no
effect.
1 = Overcurrent condition on HVDD has occurred
0 = No overcurrent condition on HVDD has occurred
High-Side Overcurrent Flag Bit (HS_OCF)
This read/write flag is set on an overcurrent condition at
the high-side driver. Clear HS_OCF and enable the high-side
driver by writing a Logic [1] to HS_OCF. Reset clears the
HS_OCF bit. Writing a Logic [0] to HS_OCF has no effect.
1 = Overcurrent condition on high-side drivers has
occurred
0 = No overcurrent condition on high-side drivers has
occurred
Low-Voltage Bit (LVF)
This read only bit is a copy of the LVF bit in the Interrupt
Flag Register.
1 = Low-voltage condition has occurred
0 = No low-voltage condition has occurred
High-Voltage Sensor Bit (HVF)
This read-only bit is a copy of the HVF bit in the Interrupt
Flag Register.
1 = High-voltage condition has occurred
0 = No high-voltage condition has occurred
H-Bridge Overcurrent Flag Bit (HB_OCF)
This read/write flag is set on an overcurrent condition at
the H-Bridges. Clear HB_OCF and enable the H-Bridge
driver by writing a Logic [1] to HB_OCF. Reset clears the
HB_OCF bit. Writing a Logic [0] to HB_OCF has no effect.
1 = Overcurrent condition on H-Bridges has occurred
0 = No overcurrent condition on H-Bridges has occurred
Register Name and Address: SYSCTL - $03
Bits
7
6
5
4
3
2
1
0
Read
PSON
SRS1
SRS0
0
0
0
0
0
Write
GS
Reset
0
0
0
0
0
0
0
0
Table 11. LIN Slew Rate Selection Bits
SRS1
SRS0
LIN Slew Rate
0
0
Initial Slew Rate (20 kBaud)
0
1
Slow Slew Rate (10 kBaud)
1
0
High Speed II (8x)
1
1
High Speed I (4x)
Register Name and Address: SYSSTAT - $0c
Bits
7
6
5
4
3
2
1
0
Read
HP_
OCF
LINCL
HVDD
_OCF
HS_
OCF
LVF
HVF
HB_
OCF
HTF
Write
Reset
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
908E626 Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908JKJK3JL3FS 68HC908JK1/JK3/JL3 8-Bit Microcontroller
909-0010 PUNCH 9 WAY D REAR MOUNT
909-0020 PUNCH 15 WAY D REAR MOUNT
909-0030 PUNCH 25 WAY D REAR MOUNT
相關代理商/技術參數
參數描述
908E625_07 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
908E625_10 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
908E626 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
908E626_09 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*